Triple Cold Shoe Mount Expansion Bracket - Free 3D Print Model

Search models, users, collections, and posts

GAWEICHAN

Hobby & DIY>Other Hobby & DIY

IP Report

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

1.2 h

2 plates

4.5(18)

Hot shoe splitter 100% infill 0.12mm layer height, 2 walls, 100% infill

Designer

3.4 h

1 plate

5.0(1)

Hot shoe 1-to-3, 100% infill (mount a little loose) 0.12mm layer height, 2 walls, 100% infill

Designer

3.4 h

1 plate

3.7(3)

Open in Bambu Studio

Boost

109

335

338

192

Released

Description

Content has been automatically translated.

Show original

Because it uses many small items, the strength requirement is not high. PLA printing is recommended. To match the Christmas elements, a Christmas hat has been added. You can glue it on.

Boost Me (for free)

Comment & Rating (26)

@Domicidal

Boosted

READ BEFORE YOU PRINT Print in PETG or stronger. Print the threaded screw at 100% infill (set walls to 1000) and fill in the hole on the bottom of the screw piece with a cylinder. This piece broke twice when I printed it at 20% and 40% infill, though I was using some force trying to get it on a coldshoe. The part is just too small to not use 100%, and it only uses a few grams of filament. 2. It threads easier if you print the threaded base at 0.12 mm. I used pliers to thread it onto the coldshoe adapter piece. Now I fully trust this print to hold lights and other small accessories. An amazing design aside from those two suggested improvements. Thank you for sharing this!

The designer has replied

@GAWEICHAN

Updated two versions, thank you for your support

Show original

@WalterEgo

Print Profile

0.2mm layer, 2 walls, 15% infill

Exceptional, exactly what I was looking for, fast, perfectly sized, reliable, and a stunning design Thank you very much

Show original

@reddotgeek

Printed with PETG. Bottom screw and nut works well with 100% infill. The top "splitter piece" is too tight and will not fit anything properly. I had to reprint at 103% scale and it still required filing... Not sure, maybe my filament shrunk too much after print. But everything turned out well, this can hold quite some weight. Thanks for sharing!

@user_3158928058

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

nice

@user_3030163657

Print Profile

Hot shoe 1-to-3, 100% infill (mount a little loose) 0.12mm layer height, 2 walls, 100% infill

screw didn’t thread, cold shoe tab was too wide for Nikon Z 6ii

@LayerMaker

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed in pla, it holds small weight, like a microphone or a light panel

@Sovianka_67

Print Profile

0.2mm layer, 2 walls, 15% infill

no solidity at all

Show original

@Domicidal

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

This print profile is probably fine for very lightweight things, but I think there are a couple improvement that can be made to this print profile for PETG. This allows it to be used for heavier accessories and last longer. 1. The threaded screw should be printed at 100% infill (set walls to 1000) and there should be a version without the hole on the bottom of the screw piece/rectangular base. This piece broke twice when I printed it at default and slightly higher infill values, though I was using some force to get it tight on a coldshoe. The part is just too small to not print it solid, and it only uses a few grams of filament to print it 100% solid. 2. The threaded screw should be printed at 0.12 mm layer height to make it easier to thread onto the triple coldshoe adapter piece.

(Edited)

@EnricoLuzi

Print Profile

0.2mm layer, 2 walls, 15% infill

The screw threads on the support are slightly tight, hindering smooth operation

Show original

@reaperxtk

Boosted

finnaly i can put DJI Mic 2 TX and RX on my camera

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.