Bosch GTS 10 XC Vertical Featherboard - Free 3D Print Model

Search models, users, collections, and posts

microgen

Hobby & DIY>Other Hobby & DIY

IP Report

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 6 walls, 30% infill

3.9 h

2 plates

4.9(34)

Open in Bambu Studio

Boost

210

763

574

314

Released

Description

Vertical Featherboard for the fence of the Bosch GTS10XC.

You'll need per set

1x Featherboard
1x Top Bracket
2x Slot Nut
4x Knob (Update 19.12.2022: Knobs designed a bit smaller to ensure better handling)
4xM6 Hex bolts
2x M6x20 for the upper knobs
2x M6x15 for the fence knops

Note, that you can use my knobs in 4 ways:

Hex bolt head in the knob, nut on the counter part
Hex bolt head in the counter part, nut in the knob
Nut in knob, nut in counter part, threaded rod cut to length and glued to knob nut (Loctite recommended)
Nut in knob, nut in counter part, threaded rod cut to length and glued to counter part nut Loctite recommended)

Using the best suitable way for you also allows to use longer Hex bolts than specified, also 4x M6x20 are possible. Use what you have in stock.

Assembly (with my way to use the knobs):

Use super glue to install the M6x15 Hex bolt into the slot nut (2x)
Install the slot nuts into the fence groove; they can be installed from above
Use super glue to instal a M6 nut into the knob (2x)
Install the Top Bracket and secure with the knobs
Use super glue to install the M6x20 Hex bolt into the knob (2x)
Use super glue to install the M6 nut into the Top Bracket (2x)
Install the Featherboard onto the Top Bracket and secure with the two M6x20 knobs

The Featherboard can support stock material of up to 53 mm and can be extended 40 mm away from the fence; minimum cut width 10 mm (Featherboard thickness = 8 mm + 1 mm play left and right side).

See my Vertical Featherboard assembly for more details!

My print settings

PLA
0,3 mm
30% 45 Infill
100% infill for the slot nuts

Please let me know your opinion on the design and feel free to provide design optimization suggestions!

Have fun!

Comment & Rating (41)

@boris.plintovic

It also fits perfectly on the Bosch GTS 635-216

@user_3855114118

Having issues with the vertical_featherboard.stl - only me? Im using flashprint and are very new to this! Cannot select only the vertical featherboard

@dymo4

Im a bit annoyed , I scaled up the board , to make it bigger and stronger . but now is a bit to thick and my push stick is hitting the screws , that as well i have installed back to front , so yeah , i have to redesign everything again . I redesign everything to be able to accommodate screws I've had , but didn't think about making everything flushed with thin feather board you have made !!!!

(Edited)

@dymo4

Print Profile

0.2mm layer, 6 walls, 30% infill

Good stuff!!!!

@user_833658826

I made it a bit thicker by simply raising the Z-axis a bit Perfect

Show original

@user_115921525

Print Profile

0.2mm layer, 6 walls, 30% infill

Sorry for the long delay, I had to stop a few times 😢 because my nozzle wasn't doing what it was supposed to, the print was incorrect. I wanted to clean it and couldn't get it out by hand, no chance, only with force 🫣 but everything went well 😅👍 I wanted to give you full points for this. Great work and thanks for sharing

Show original