Zelda Breakable Jar Ocarina of Time 3D - Free 3D Print Model

Search models, users, collections, and posts

Toadhex

Props & Cosplays>Other Props & Cosplays

IP Report

GIF

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 3 walls, 15% infill , Brim, Support

Designer

8.2 h

6 plates

5.0(16)

Open in Bambu Studio

Boost

742

1865

559

175

Released

Description

Breakable jar from the Zelda Ocarina of Time 3D version.

Be sure to use support and brim as the print has pointy areas. I used PLA to print the model, I haven't tested any other filament types but those shouldn't cause any problems.

The jar and rupees are handpainted using acrylic paint!

The rupees were used from https://makerworld.com/en/models/539832?from=search#profileId-457190 , Much thanks to this creator!

I used 6x2mm magnets for this build (40x required). The holes have been made a bit bigger to more easily fit the magnets.

Boost Me (for free)

Comment & Rating (42)

@Apothicc

The print profile is no longer public

Bed Adhesion Issue:I had to add a 5mm brim and additional supports at 40 degrees vs standard to get the bed adhesion to work for 3 of the pieces. This print failed 3 times and I wasted roughly 150g of material. However I got it to finally print. Not sure if there is too much on the plate or splitting it with the supports helped. I cleaned the plate and don't have issues with other prints. They both let go around 2 hours in. X1C with PEI textured plate

The profile uploader has replied

@MamaDragon

I had a similar issue. I'm hoping OP will be able to separate the pieces. It is a fantastic concept and design. Perhaps just a simple overloading the plate.

(Edited)

@Toadhex

Hey, sorry to hear that you have wasted so much filament, i will make a new profile that will address these problems!

(Edited)

@StudBrownie

Replying to @MamaDragon :

This one is guarateed to work https://makerworld.com/en/models/1023863-breakable-zelda-pot-with-rupee#profileId-1005695

@user_1922203303

Boosted

Printed them as gifts, turned out nicely. ⭐⭐⭐⭐⭐ I noticed that there's this rough texture that shows up on the surface of some of the pieces (two corresponding spots shown in the second picture, circled in red), I wonder how I can avoid this. I don't know if it's a printer issue (I have a P1S).

The designer has replied

@Toadhex

Mmmh normally all the rough sides should be on the inside, I think something went wrong with your print but i cant determine what happend honestly :(.

@user_1922203303

Boosted

Replying to @Toadhex :

Yeah not sure, and it's funny how it is the same exact spots on the two pots. Well, since I'm printing a third pot (my little brother saw them and asked for one too 😂), I think I'll change the position of the pieces on the plate and also try printing at 50% speed. if it helps with getting rid of that rough texture, I'll let you know 👍

@rotgot23

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

Came out really well and was fun to build. Just used normal super glue from Woolworths and magnets of Amazon.

@Kimyo

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

I LOVE this. It came out so well. Quality was pretty good directly from the print profile. I deleted the brim and didn't have any problems with adhesion.

@Hony684

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

nice, ty

@Filamently

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

Soo fun - everyone loved this when I showed it off to family and friends! Makes a great addition to my collection of Zelda-themed stuff!

@Owl3DPrints25

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

this was a gift for my husband that really loves this. but it is now my daughter's favorite toy!

The profile uploader has replied

@Toadhex

Lovely to hear that <3 !!!

@moonrakerone

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill , Brim, Support

Excellent

The profile uploader has replied

@Toadhex

Thanks for your review and boost!

@PrintingStuff1

printed on a P1S using Bambu Wood PLA no brim with tree supports, turned out great.

(Edited)

@MamaDragon

Is there a way to print each piece individually? I'm working from the phone app, no computer/studio. I would happily boost if that's an option.

The designer has replied

@Toadhex

Hey! I will add this asap!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.