BUY嘉筆記

cover

Image 636_9663b8da-8422-447f-9f25-ab0598753b62.png

1727196140232.jpg

1724119216543.jpg

plate_1.png

1729504175024.jpg

1729504078095.jpg

1729504078089.jpg

測試方塊印完就沒用了.我在想有沒有可以擴展測試方塊的用途所以這個測試骰子.測試完也可以用來娛樂.減少資源浪費

The test cube is useless once it's printed.I was wondering if there was a way to expand the use of the test cube.So this test die, after testing, can also be used for entertainment. Reducing resource waste.

15mm測試骰子0.2mm layer, 2 walls, 15% infill

縮小為15mm大小可以更快速的列印測試

Scaled down to 15mm sizeAllows for faster print testing

15mm size, prints faster, 0.2mm layer, 2 walls, 15% infill

1734595381723.jpg

1734595381680.jpg

1734595381704.jpg

1734595381696.jpg

1734595381688.jpg

1734595381710.jpg

1734595381717.jpg

It is recommended to print the basic version first. If it prints perfectly, then test the advanced version.Tests above 45 degrees are meaningless. Normal machines can print perfectly at temperatures above 45 degreesThere is a high chance that the advanced version will not print well in the test. Please do not give a rating below 5 stars just because the advanced version does not print well.I can’t print well at 20 and 21 degrees either.建議先列印基礎版. 若能夠完美列印.再進行進階版測試45度以上的測試不具意義.正常的機器都能完美列印45度以上進階版測試有很大機率印不好.請不要因為進階版印不好就給低於5星的評價我自己 20與 21度也印不好

It is recommended to print the basic version first. If it prints perfectly, then test the advanced version.Tests above 45 degrees are meaningless. Normal machines can print perfectly at temperatures above 45 degreesThere is a high chance that the advanced version will not print well in the test. Please do not give a rating below 5 stars just because the advanced version does not print well.I cannot print well at 20 and 21 degrees either.It is recommended to print the basic version first. If it prints perfectly, then proceed with the advanced version testTests above 45 degrees are meaningless. Normal machines can perfectly print above 45 degreesThere is a high probability that the advanced version will not print well. Please do not give a rating below 5 stars just because the advanced version does not print wellI myself also cannot print well at 20 and 21 degrees

Angle Test: Please print the Basic version first, then challenge the Plus version

2024-08-20_7214d6fc23bac

耗材第一次使用可列印此測試方塊.取得公差值設計組裝件時可預留公差值.可加快開發進度.減少耗材浪費.When using the filament for the first time, you can print this test box and get the tolerance value.Tolerance values can be reserved when designing assemblies.To speed up development progress and reduce waste of consumables.

Print this test cube with the filament for the first time, obtain the tolerance value.Tolerance values can be reserved when designing assemblies.To speed up development progress and reduce waste of consumables.When using the filament for the first time, you can print this test box and get the tolerance value.Tolerance values can be reserved when designing assemblies.To speed up development progress and reduce waste of consumables.

Small printing tolerance test cube 0.2mm layer, 2 walls, 15% infill

webbuster

IMG_20240710_201912.jpg

Al is great the A1 mini printed great and the dimension are ok

0.2mm layer, 2 walls, 25% infill

PolyFox

2024-10-21_971b2aa285c91.webp

PETG - Test Cube

<boostme><boosttitle>Boost Me</boosttitle><boostcontent>BOOST對設計者而言是最佳的鼓勵,或是五星評價也是絕佳的動力支持.</boostcontent></boostme>12/19新增極限角度列印測試如果連45度都印不好.這很嚴重,請檢查線材參數或是先烘好線再印一次.PLUS版本印不好是正常的,請不要因此給低於五分評價&nbsp;8/14新增1CM組裝公差測試方塊.通常印0.1~0.3即足夠測試印好後透過X-Y-Z方向組合.依據鬆緊來決定設計時的公差值.&nbsp;測試新機台的方塊

<boostme><boosttitle>Boost Me</boosttitle><boostcontent>Boosting is the best encouragement for designers, or a five-star rating is also excellent motivational support</boostcontent></boostme>December 19Added extreme angle printing testIf even 45 degrees cannot be printed well, this is serious, please check the filament parameters or bake the filament before printing againIt is normal for the PLUS version to print poorly, please do not give a rating lower than five stars&nbsp;August 14Added 1CM assembly tolerance test cubeUsually printing 0.1~0.3 is sufficient for testingAfter printing, combine it through the X-Y-Z directions, and determine the tolerance value during design based on the tightness&nbsp;Test cube for new machines

Print Profile(6)

Description

Comment & Rating (1000)

License

Remixes (2)

Related Models

TEST-CUBE