Traxxas TRX4M Defender Pickup Body & Accessories

Copyright Claim

Traxxas TRX4M Defender Pickup Body & Accessories

Boost
102
177
23

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
7.2 h
1 plate
5.0(3)

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
2.5 h
1 plate
5.0(3)

Open in Bambu Studio
Boost
102
177
23
7
211
22
Released

Description

Here we have the latest TRX4M design

A full Defender double cab pick-up styled body and accessories. Within the STLs you will find:

  • Body
  • Interior (clips into body, bo glue required)
  • Roll Bars (slots into pickup bed)
  • Spare wheel (slots into pickup bed)
  • Front Mirrors (clip in)
  • Door handle (print 4 times. depending on printer tolerance, may need glue)
  • Rear lights (individual lenses so can be coloured)
  • Front lights (left and right)

Mounting: the body itself is designed to mount to the origional mudguard sub frame from the defender, meaning no extra kit needed, just the original screws

 

Instructions: 

  1.  Remove the 2 screws from the back of the radiator panel
  2. Remove the 6 smaller screws from the body. 
    1. 2 x Front left and right corners
    2. 2 x Mid left and right
    3.  2 x Rear left and right corners

  3. pull original body from the mud guard sub frame
  4. put new body on to sub frame, ensuring the 6 notches for screws line up with the holes
  5. insert the 2 larger grille screws and tighten hand tight
  6. Replace the 6 smaller screws from the body in this order. 
    1. 2 x Front left and right corners
    2. 2 x Mid left and right
    3.  2 x Rear left and right corners
  7. glue in the respective lights for front and rear
  8. (optional) insert an accessory piece into the bed 
  9. (optional) insert the interior piece, which simply just clips in via 3 clips into holes in the body, no screws required

The 3mf provided uses a raft as i found the bed would peel to to length of print and small surface area. This means that the rear of the body (boot/tail gate) will show marks from the raft removal, so you may want to sand it down. feel free to try a print without the raft though if your bed is good

 

Any requests for extras or changes, please do let me know and I will do my best to accomodate

Comment & Rating (23)

Please fill in your opinion
(0/5000)

Thanks for making the file
The designer has replied
1
Reply
looks great! thanks for sharing
1
Reply
so where can I find the accessories? STL file?
The designer has replied
0
Reply
on the Bambu site, if you click the green button dropdown where it says open in Bambu studio, then click download, you will download all the STLs
0
Reply
I’ll add them as seperate plates tonight too so they are easier to get to
1
Reply
ok thank you! also if I do remix it is it ok? I don’t want to remix it without permission, also thanks!
0
Reply
anyways good job on this
The designer has replied
0
Reply
thanks!
0
Reply
hello again, I love this body and just bought the fender flares and I found a problem, where the front windshield, I see the 2 tiny screw hole and I see them breaking. so maybe that’s something fixable, will I’m not sure but i will figure out something because Traxxas don’t give any screws for it so yeah… thanks
0
Reply
also I’m going to make the grill.
0
Reply
https://www.thingiverse.com/thing:5752481 don't be dumb like me needing a grill for this defender body. check this file on thingverse if doing a new body.
The designer has replied
0
Reply
thanks for the review and comment, great find on the grill!
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
same as the body. very cool print and fit well. only part that doesn’t seem quite right was the steering column to the wheel but that coulda been my mistake also
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
very cool body. fit perfectly with the fenders. if you have a trx4m defender I recommend printing this. will not disappoint
0
Reply
Very nice
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Very great again! nice prints!
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.