Shadow Sonic - multi part

Remixed by
Copyright Claim

Shadow Sonic - multi part

Remixed by
Boost
356
596
76

Print Profile(2)

All
A1
P1S
P1P
X1 Carbon
X1E
X1

0.16mm layer, 2 walls, 10% infill
0.16mm layer, 2 walls, 10% infill
Designer
44.7 h
9 plates
4.8(34)

0.16mm layer, 2 walls, 10% infill
0.16mm layer, 2 walls, 10% infill
Designer
6.4 h
1 plate

Open in Bambu Studio
Boost
356
596
76
80
886
257
Released

Description

Content has been automatically translated.
Show original

A 37cm tall multipart shadow.

 

A remix of the model in higher resolution, smoothing all parts for a better finish.

Everything was printed with normal orientation and supports as in the 3MF file.

 

A slight gap between the eyes and the muzzle, the red head inserts are quite difficult to print, it is really necessary to reduce the speed (for information with the 0.16mm high-quality profile I reduced it by 50%).

All parts are marked LT and RT, sort the parts well after printing.

For assembling the shoes, tenons are present.

Assemble the shoes completely before attaching the body as shown in the photo.

 

The red head inserts are quite difficult to print, I recommend strongly reducing your speed.

 

Happy printing everyone.

Comment & Rating (76)

Please fill in your opinion
(0/5000)

printed most parr’s fine but when started to print the legs and body, the same arm fell of the support twice!! once while using tree supports and ince while using normal supports. really annoying. any chance anyone can split that part into two, and I can stick them together.
(Edited)
The designer has replied
2
Reply
Hello, have you tried the inverted body? Orienting the feet upwards also works I will look into severing the arms from the body as soon as possible
Show original
0
Reply
Replying to @Ethanprint3D :
hi, no I haven’t, is there a setting for this? or do I turn it around myself. so sorry to ask, very new and this is probably a bit ambitious but just thought it is ao cool!
(Edited)
0
Reply
Replying to @user_2141453867 :
I will cut it for Monday, so we can print the arms separately, and yes, it is not a simple model to print
Show original
0
Reply
Print Profile
0.16mm layer, 2 walls, 10% infill
It’s not quite as high-quality as its counterparts, but still quite nice
Show original
1
Reply
can you point me to where I can get sonic, nuckles, tails high rest file to print?
(Edited)
0
Reply
For Sonic: https://makerworld.com/models/178904 profile 200% For Tails, the same person as Shadow or Sonic (depending on the desired orientation) For Knuckles: https://makerworld.com/models/728984 but it is not enlarged, you will have to do it in Bambu Studio
(Edited)
Show original
1
Reply
Print Profile
0.16mm layer, 2 walls, 10% infill
Our biggest print to date, was indeed a learing curve but we got it done and it looks amazing! printed head spikes pointing upwards, used extra strong tree supports. And printed legs pointing ipwards and turned side ways, see pics if unclear. had two fails on legs standing and ne fail on head with spikes pointing downwards.
The designer has replied
1
Reply
bravo
0
Reply
the white eye lid and the face is a little not align/even theres a gap, or I did something wrong on the glueing that I made, I think I should glue the face 1st then the white eye lids and the eyebrows and later the eyes. send pic, the hand red and yellow and black theres no dowel, I just eyeball and glued it. a very long time to print and hard to glue cause I use liquid my fault it had smudge shadows face and chick. done printing and glueing, I don't know if I made a mistake cause shadow stands a little not flat on the shoe, might be my fault. the ankle yellow to the grey part (dowel to big need to make the hole deeper on the grey part). Happy on the built, thank you so much. hope there will be tails and knuckles and sonic.. already boosted. btw I printed the red parts 2x.
(Edited)
The designer has replied
1
Reply
Regarding the pegs at the hand level, there are no pegs; the slots exist, but they were too small to print, so I removed the pegs from the file There is also a slight misalignment between the white eyes and the muzzle, unfortunately
Show original
0
Reply
I printed it %50 scale. My little cousin loved it. There is a little problem with alignment but not that of a issue
1
Reply
Print Profile
0.16mm layer, 2 walls, 10% infill
printed great Thank-you
1
Reply
Boosted
Print Profile
0.16mm layer, 2 walls, 10% infill
Magnificent print, bravo
Show original
1
Reply
excelente
1
Reply
Print Profile
0.16mm layer, 2 walls, 10% infill
I won my son's bday best gift ever award.
1
Reply
Print Profile
0.16mm layer, 2 walls, 10% infill
molto bello
1
Reply