AMS Label Holder

AMS Label Holder

Boost
26
75
15

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

Use with Standard AMS Lid (No Hygrometer Mount)
Use with Standard AMS Lid (No Hygrometer Mount)
Designer
1.5 h
1 plate

Use with Hygrometer Holder (Rectangular Base at Lid Handle)
Use with Hygrometer Holder (Rectangular Base at Lid Handle)
Designer
1.6 h
1 plate
5.0(1)

Open in Bambu Studio
Boost
26
75
15
2
19
15
Released

Description

So, I created a label holder that can be used for a dry box or storage container for filament (https://makerworld.com/en/models/902107?from=search#profileId-861335).  I glued these to my storage boxes (https://www.amazon.com/dp/B07HRKJYJF?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1) and cut the filament info from the cardboard Bambu boxes that ship filament refills to use as labels.  When I moved filament from storage to my AMS or vice versa I’d simply switch labels.  The problem that arose was that I would always have the four labels for the filament in my AMS just lying around.  Enter this label holder for the filaments in the AMS!  Is it absolutely necessary?  No, but not many things in life are.  It solved a problem I had and I hope you find it useful too (even if you aren’t currently using my filament label holders, which you should).

 

I designed mine to fit around an external hygrometer mount designed by another user which has a rectangular base.  I’ll try to post one for the standard AMS lid (round handle) too.  In each case, you should just be able to press each half of the holder around the base of the handle used for lifting the AMS lid.  You can affix it with two-sided tape, but mine works well without it.  Enjoy, and .et me know if you have any questions or suggestions for improvement. 

 

Boost Me (for free)

If you like this model, please consider giving me a boost!

Comment & Rating (15)

Please fill in your opinion
(0/5000)

Boosted
FOr some reason mine do not fit under the AMS handle (tried three different ones). Seems the cutout part is too thick.
The designer has replied
0
Reply
Thank you for reaching out. I'm sorry that your initial prints didn't fit. I measured my AMS and initially designed the holder to have about 0.2 mm clearance. I've updated the print profile to decrease the thickness of the bottom of the holder by close to 2 mm (should be 5 mm now) since the fit around the handle should be tight enough to hold the holder in place without a snug fit under the handle. The profile has the same name, but the new file ends in "-short". I hope this helps. Please let me know if you try again.
0
Reply
Boosted
Replying to @elsandmaker98 :
Thank you for the quick response. The new thickness is perfect. However, (hate the fact I couldn't check it before) the size of the semicircle is too small (I printed some partials to verify so it does not go all the way in. I wonder if that was a change to recent AMSs as all three of mine are less than a month old. If you get a chance to change it, I will print and verify asap. Thanks again.
(Edited)
0
Reply
Replying to @RickMz :
I took my handle off and measured again and made changes to the semicircle (file name is the same, but with “-short v2” at the end. This one should fit around the handle, but it might not be a tight fit so you might have to use 2-side tape to hold the whole thing down. Thank you so much for the feedback and collaboration!
1
Reply
Boosted
Print Profile
Use with Hygrometer Holder (Rectangular Base at Lid Handle)
Great idea and good execution. Printed three for my AMSs. Thanks for the effort.
The designer has replied
1
Reply
Thank you very much!
0
Reply
Boosted
Great concept and quick communication / action.
The designer has replied
1
Reply
Thank you for the boost!
0
Reply
are those holders different sizes? the outside ones look wider.
The designer has replied
0
Reply
They are the same size. They probably look that way because of the cutout for the arms that hold the lid down.
0
Reply
Replying to @elsandmaker98 :
thanks!
0
Reply
No more