Bamboo Bambu Lab - Filament Painting

Copyright Claim

Bamboo Bambu Lab - Filament Painting

Boost
8
15
0

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

1 AMS
1 AMS
Designer
2.7 h
1 plate

2 AMS
2 AMS
Designer
2.7 h
1 plate

NO AMS
NO AMS
Designer
2.6 h
1 plate

Boost
8
15
0
0
20
3
Released

Description

This is a 5 color Hueforge filament painting that I made for my AMS DECO stand/frame. This model was designed as a decorative plate to sit in front of the AMS, but can be put anywhere.

*

 

This print takes just under 3 hours and is 5 colors. It can be printed easily by people with or without AMS units. If you have an A1 mini or any other printer with a bed smaller than the capacity to print 250mm x 75mm you can use the slicer to scale the model in the correct profile for your multi color setup just make sure NOT TO SCALE THE Z dimension.

*

 

IMPORTANT: READ BEFORE PRINTING

*

 

I have uploaded three 3MF profiles. One for people with a single AMS, one for people with two AMS units, and one for people with NO AMS.

*

 

To print with 1 AMS you need to swap out AMS slot [1] (Color [1]) with Color [5] when the black [Color 1] has completed and fully retracted. Once the second color starts printing just load the new spool. Note the AMS will not feed the spool like it does pre print but as long as you have fed 3-4 inches in there and the light goes on it will feed as normal when it swaps back to the last color in AMS [1]

*

 

To print with 2 AMS units all you need to do is load the colors in order and print.

*

 

To print with NO AMS unit you just need to do manual filaments swaps every color. The 3MF is set to pause at the correct layer heights. At each pause load the next filament color in order by following your unload/load procedure for your particular printer, then hit resume. Repeat until complete. This will be once per color over the entire painting. You have a decent amount of time between swaps, and is actually harder to mess up because it pauses unlike when using the AMS.

*

 

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. There are some recommended speed changes in my 3MF files and a layer height modifier to print the first 0.80 mm @ 0.16 mm layer height to speed up the print as there is no blending on those layers.

*

 

Like all of my models this is strictly for personal use. The photo attached is the printed model and AMS DECO frame.

*

 

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA PolyLite Jungle Green Transmission Distance: 0.5
PLA BambuLab Basic BambuLab Green Transmission Distance: 8
PLA PolyLite Yellow Transmission Distance: 10
PLA BambuLab Basic Jade White Transmission Distance: 5

*

 

Swap Instructions:
Start with Black
At layer #12 (1.12mm) swap to Jungle Green
At layer #18 (1.6mm) swap to BambuLab Green
At layer #24 (2.08mm) swap to Yellow
At layer #30 (2.56mm) swap to Jade White for the rest.

*

 

If you print this model please post makes, like the post and rate it. Thank you in advance to those who do.

Comment & Rating (0)

Please fill in your opinion
(0/5000)

No more

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.