Thermometer Hygrometer Stand – Retro Television

Copyright Claim

Thermometer Hygrometer Stand – Retro Television

Boost
1099
1943
185

Print Profile(12)

All
P1P
P1S
X1
X1 Carbon
X1E
A1
A1 mini

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
1.4 h
2 plates
5.0(87)

A1 Mini (0.2mm layer, 2 walls, 15% infill)
A1 Mini (0.2mm layer, 2 walls, 15% infill)
Designer
1.6 h
2 plates
4.8(11)

no supports, 1 plate, ventilation, panel/dial colorswap
no supports, 1 plate, ventilation, panel/dial colorswap
1.4 h
1 plate
5.0(25)

Ventilated Cover - 0.2mm layer, 2 walls, 15% infill, 1 plate
Ventilated Cover - 0.2mm layer, 2 walls, 15% infill, 1 plate
1.2 h
1 plate
4.9(18)
Click to see more

Open in Bambu Studio
Boost
1099
1943
185
162
1.5 k
805
Released

Description

📺Decorative stand for Hygrometer / Thhermometer that fits in every home! Simply insert the thermometer into the hole in the retro TV.. Insert the face into the case and secure with the legs! So simple 😎.

🔋When replacing the battery, the face can be slid out of the case. Push the face out using a thin object through the threaded hole for the leg.

 

Bill of Materials

Buy Now
Download BOM

Comment & Rating (185)

Please fill in your opinion
(0/5000)

Boosted
Great idea! I had a few of these hygrometers just sitting around in a few rooms, so this will be a nice improvement. I also picked up on the airflow issue and went a bit further with it than you did. I used the 'make overhangs printable' feature in orcaslicer to print it without supports, but I didn't pay very close attention to the slice and didn't realize it blocked some of the holes 🤦‍♂️. I drilled them out and they still worked fine, but it should be a pretty easy fix to add some slopes around the top rim to eliminate the need for supports (it adds 1-2g filament but saves 3-4g support). To heighten the retro aesthetic I added some glow in the dark filament to the tips of the dials, and I think adding a color swap to a wood or metallic color for just the panel/dials would look nice (will update). One other minor thing is that , IMO, two of the feet should be printed flipped so that the surface showing on the legs (bottom/top surface) is consistent between the left and right. Print profile with my changes coming soon™
2
Reply
Boosted
Print profile added
1
Reply
Thanks for remix! With Spectrum Wood Oak PLA and Spectrum Glitter Aurora Gold PLA came adorable!
1
Reply
Love the design, however, drawing inspiration from another Hygrometer stand and a bit born out of the annoyance that appears when it's a on a slight angle and you can't see the temp/humidity - I Remodeled to have more holes in the back and a bit slimmer to compensate for the filament that it adds with the stand. Still 30g, still 1h 40m to print. Still a super nice original design! Profile uploaded. Thanks for sharing this design.
2
Reply
Print Profile
no supports, 1 plate, ventilation, panel/dial colorswap
nice desgin and looks great, but the two legs on the right does not sit at the correct orientation, but i suspect its the printer issue because i can tell the flow calibration did not compensate properly....anyway keep up the fun ideas.
The designer has replied
0
Reply
Boosted
I found that they will rotate more, but it's quite tight -- I used some pliers to get enough grip to keep turning them in the right orientation.
0
Reply
Replying to @.cs. :
the pliers helped...i appreciate replying back
0
Reply
Boosted
Print Profile
no supports, 1 plate, ventilation, panel/dial colorswap
This design is unparalleled
Show original
1
Reply
Nice and cute! Printed successfully with nice finishing. A1 Mini with Tri colors PLA+.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Extremely easy print Absolutely superb
Show original
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Looks really good 👍. I tried PLA and PETG; PETG turned out better and didn't print all pieces in one color.
0
Reply
This is incredibly cute! thank you!
0
Reply
Print Profile
Ventilated Cover - 0.2mm layer, 2 walls, 15% infill 2 plates
love it
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Thanks to the model.
GIF
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.