curved lithopane stand for tea light candle

Copyright Claim

curved lithopane stand for tea light candle

Boost
38
87
29

Print Profile(3)

All
A1
P1S
P1P
X1 Carbon
X1E
X1
A1 mini

0.16mm layer, 4 walls, 100% infill
0.16mm layer, 4 walls, 100% infill
Designer
25 min
1 plate
5.0(7)

0.16mm layer, 4 walls, 100% infill
0.16mm layer, 4 walls, 100% infill
Designer
1.1 h
2 plates
5.0(1)

0.16mm layer, 4 walls, 100% infill
0.16mm layer, 4 walls, 100% infill
Designer
1.2 h
2 plates
5.0(1)

Open in Bambu Studio
Boost
38
87
29
3
87
52
Released

Description

Hello,

here is my design of a curved lithopane stand that holds a tea light candle at a very safe distance from the lithopane and brightens up really well,you could also use a battery operated tea light, please note this has been tried and tested and we have been using these stands for around 7 months and had no problems at all i hope you enjoy .

 

1st print profile 

This is for 75 ' degree angle curved lithopanes 

This is for 3mm thick curved lithopanes upto 150mm wide i have not tested any bigger than the 150mm 

 

included is the stl and 3mf files.

 

UPDATE : i have added 2 more print profiles as requested

 

2nd print profile is beefy bulkier slightly heavier and holds bigger curved 75 degree lithopanes 3 mm thick - short leg version is on plate 1 and long leg version on plate 2.

 

3rd added new print profile its heavier and has a 3 degree tilted backwards for more light exposure it holds taller lithopanes short leg version is on plate 1 and long leg version on plate 2.

 

Please upload your prints with the lithopanes i would like to see your creations enjoy and thank you all for downloading … enjoy …

 

Boost Me (for free)

Like my designs? then please BOOST me for FREE to support this creation and further ones to come !! Thank you in advance greatly appreciated:) if you want to sell any of my models my patreon will be available soon

Comment & Rating (29)

Please fill in your opinion
(0/5000)

Boosted
Print Profile
0.16mm layer, 4 walls, 100% infill
I like the simpel design, printed well. Don't know if there's an issue with the litho that I printed or the angle of the holder but it's kind of balancing and almost tipping forward. would be great if there was a bit of an angle tilting the litho a bit towards the light.
The designer has replied
1
Reply
as promised a new and stronger version for bigger curved lithopanes there is the normal original size just beefed up a bit then theres the longer leg version both have minor changes but enough to withstand the weight of a 188cm tall lithopane hope you enjoy. sorry for the delay
1
Reply
Boosted
Replying to @eyedoo3d :
awesome! looks promising, will try it! 😀
0
Reply
Replying to @Agw89 :
let me know if its suitable for you if not i could change it so its angle is on a slant by 5 degrees i didnt implement that in this design but i can change it if needed. all feedback is appreciated good or bad its how we improve.
1
Reply
Print Profile
0.16mm layer, 4 walls, 100% infill
Works great, cute little print. Thank you.
The designer has replied
0
Reply
im glad you like it thank you i have uploaded new versions short leg and long leg not sure if you have seen them there is a 3 degree curve tilted more towards the light
0
Reply
Your stand is simple and elegant. I printed a frameless litho that is 188mm in height. It tends to fall over. :( Is my thinking correct in that the legs need to be longer?
The designer has replied
0
Reply
thank you for the kind reply i havn't tried a 188mm tall lithopane but i will take a look maybe i need to change something to accomodate bigger and taller lithopanes i will upload another version today or tomorrow when i get chance again thank you for pointing this out although the stand is for upto 150mm wide and 150mm tall lithopanes tried and tested with a 3mm thickness.
1
Reply
as promised a new and stronger version for bigger curved lithopanes there is the normal original size just beefed up a bit then theres the longer leg version both have minor changes but enough to withstand the weight of a 188cm tall lithopane hope you enjoy. sorry for the delay
1
Reply
Replying to @eyedoo3d :
You are AWESOME!
0
Reply
Print Profile
0.16mm layer, 4 walls, 100% infill
perfetto
The designer has replied
0
Reply
thank you hope you enjoy
0
Reply
Hello, what angle should I use
The designer has replied
Show original
0
Reply
hi 75' degree angle thanks
0
Reply
what size lithopane is this sized for?
The designer has replied
0
Reply
hi its for 3mm thick curved lithopanes also i have printed upto 150mm wide lithopanes and they fit well i have included photo of the 90 mm and 70mm wide that i generally print hope this helps .
0
Reply
Print Profile
0.16mm layer, 4 walls, 100% infill
AWESOME! THANK YOU!
0
Reply
Print Profile
0.16mm layer, 4 walls, 100% infill
EXCELLENT! EXCELLENT! EXCELLENT
0
Reply
Boosted
Print Profile
0.16mm layer, 4 walls, 100% infill
Works great 👍
0
Reply
Please let me know when your patreon is ready for licensing.
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.