If You like the stands I use!

I designed the stands that I use for my hueforge prints! If you are interested, they are on maker world which can be found here:

https://makerworld.com/en/models/583860#profileId-505016

I also have a new stand that is for Grid Panel Displays! You can check it out here!

https://makerworld.com/en/models/829108#profileId-773198

How to support me!

If you like my work, consider joining my Patreon where you can have a say in what I print next! You will also get access to my tips and tricks for making a hueforge start to finish. I offer a coaching session to some of my patreons! You will also get a commercial license to sell all my patreon exclusive hueforges and on makerworld. Finally, I began a competition where my patreons create a hueforge once a month and the winner get a $40 bambu gift card!

I have new series for patreon members only! Here are photos of the series!

Thank you for all your support!

www.patreon.com/CloudyNostalgia

Also, if you have any questions about how to print a piece of mine or if you need help troubleshooting, feel free to join my discord server where you can ask for help!

https://discord.gg/fKEjJD3n9z

Also, I upload videos every so often showing how to videos for Hueforge. If you’d like to view here is the link:

https://www.youtube.com/channel/UCG1IDrymVjUyYng7nXrdGnw

**IMPORTANT INFORMATION**

• You cannot adjust the z scaling on any hueforge. This will mess with the coloring done and your hueforge will not come out as intended. You can however change the x and y to scale the picture. I recommend only changing by the same percentage.
• To get an accurate print as shown in the photos you MUST use the same filaments listed below. You can change brands (as long as they are similar) but keep the filament colors the same. If you use any other color, you will not get the same results as me.
• What you see in the slicer will not be how the final results will look! Hueforge takes advantage of color bleed to make the blended colors!
• Be sure that you bed had really good adhesion! If not the print may lift and cause warping to ruin the print!

Follow the instructions given below if you are not using my 3mf file.

Please use the same filaments for accurate results! I cannot guarantee same results if you are using different brands.

***For Gray Version***

Project: Evil Rick and Morty.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

The Model is 187.81x235mm in size
You may print at higher layer heights below the Min Depth of 0.96mm
The Max Depth is 3.2mm and the Actual Depth is 3.3mm

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.2
PLA BambuLab Basic Blue Gray Transmission Distance: 3
PLA BambuLab Basic Gray Transmission Distance: 2
PLA BambuLab Basic Jade White Transmission Distance: 6
This print uses 4 unique filaments

Swap Instructions:
Start with Black
At layer #26 (2.16mm) swap to Blue Gray
At layer #32 (2.64mm) swap to Gray

Border Only Colors from here until the end.
At layer #35 (2.88mm) swap to Jade White
At layer #41 (3.36mm) swap to Black for the rest.

***For Gold Version***

Project: Evil Rick and Morty.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

The Model is 187.81x235mm in size
You may print at higher layer heights below the Min Depth of 0.96mm
The Max Depth is 3.2mm and the Actual Depth is 3.3mm

Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.2
PLA BambuLab Basic Blue Gray Transmission Distance: 3
PLA BambuLab Basic Gold Transmission Distance: 2.3
PLA BambuLab Basic Jade White Transmission Distance: 6
This print uses 4 unique filaments

Swap Instructions:
Start with Black
At layer #26 (2.16mm) swap to Blue Gray
At layer #32 (2.64mm) swap to Gold

Border Only Colors from here until the end.
At layer #35 (2.88mm) swap to Jade White
At layer #41 (3.36mm) swap to Black for the rest.