Glasses new years 2025 by SaVo3D

SaVo3D

Fashion>Glasses

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

0.2mm layer, 2 walls, 10% infill

Designer

1.8 h

1 plate

4.6(17)

0.2mm layer, 2 walls, 10% infill

2.6 h

1 plate

Open in Bambu Studio

Boost

178

103

Released

Description

Glasses to welcome 2025 at your new years eve party!

I replaced the model and print profile with improved earpieces which are now foldable and print separately. There were reports of bad prints caused by the upstanding earpieces before. I redesigned them and here they are!

To assemble the earpieces:

slide a piece of filament through the hole of the hinge
cut the filament flush
take a lighter and heat the filament at the top of the hinge untill it beginns to get soft, then press with a knife or something down on the hinge so the filament will not fall out
repeat the process on the bottomside of the hinge

The glasses are 155mm wide and the length of the earpieces are 145mm, this should be standard size to fit 90% of the people. If you need other sizes, simply scale the glasses in your slicer.

Recommended filament:

PLA or PETG, whatever you have

Hotend: 0,40mm

Before printing, make sure your build plate is clean and apply some adhesive. Wash the build plate with oil free soap and wipe it off with some paper towels. For a good build plate adhesion, apply a thin, even coat of your preferred adhesive. I repeat the process every 5-6 prints.

Bad build plate adhesion is not related to the model.

Take a look at my other models https://makerworld.com/en/u/1597610120

Please leave me a like and a decent rating if you were satisfied, thank you in advance!

Comment & Rating (36)

@Kosau

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

Thank you for your design, I liked it so much that I made it for everyone ^^ wiiii happy new year!

The designer has replied

@SaVo3D

thank you kindly

@cwest

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

Great design! Had some issues with the ear stems wobbling even with added supports but remixed some foldable stems on and all is good. Thanks!

The designer has replied

@SaVo3D

thank you kindly

@Berlin1982

Print Profile

0.2mm layer, 2 walls, 10% infill

Support Issue:The supports detached during printing.

Strength Issue:Some lettering fell off when removing it from the print bed, unfortunately, a bracket also broke during removal, which could only be held in place again with adhesive.

The designer has replied

Show original

@SaVo3D

Which printer are you using I imagine that problems could arise with the bedslinger A1 and A1 mini due to the movement of the print bed The print detached from the bed I don't quite understand that

Show original

@Berlin1982

Replying to @SaVo3D :

It is an X1C dampened against vibrations and with AMS moisture monitoring below 10% The print adhered to the print bed upon release (without adhesive)

Show original

@SaVo3D

Replying to @Berlin1982 :

Hmmm… the delamination of the lettering is truly perplexing, as all parts should be interconnected, eliminating this possibility The issue with the supports at the top has been reported by several users, thus I reinforced the supports in that upper area I might need to decrease the distance between the supports and the model However, this carries the risk of the supports fusing with the model, making removal exceedingly difficult

Show original

@J0k3st3r235

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

made these for the kids and they moved them. had to heat one up to make ear hold better for 7 year old but she was happy as hell.

The designer has replied

@SaVo3D

Thank you kindly! Maybe you should have scaled the glasses down for small faces, like i stated in the model description. But i am glad that you found a way to fix it. 👍

@J0k3st3r235

Boosted

Replying to @SaVo3D :

I was going to but I was afraid that I do it to much and the info on the bottles would not be readable and I printed it as I was sleeping. I work overnight so it was a 1 and done if it failed I was screwed lol. I have you followed so if you do them next year I'm going to try that.

@SaVo3D

Replying to @J0k3st3r235 :

I will add a kiddy version for next year

@rmasse10

Print Profile

0.2mm layer, 2 walls, 10% infill

fun design, but the ear pieces printed really rough

The designer has replied

@SaVo3D

Did you dial in your filament settings? I set up the print profile with support in this area so the earpice wont wobble. As you see in my print, it went flawless.