Christmas tree kit card - fast print by feder

feder

Household>Festivities

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

29 min

1 plate

4.7(35)

0.2mm layer, 2 walls, 15% infill

Designer

32 min

1 plate

4.9(9)

Open in Bambu Studio

Boost

264

337

251

Released

Description

Please note - updated version is here:

https://makerworld.com/en/models/840717#profileId-786745

The Christmas Tree Kit Card is a delightful and creative way to share the holiday spirit with family and friends. This unique, easy-to-assemble kit transforms into a charming Christmas tree that can be used as a festive decoration or even as a personalized Christmas bauble to hang on your tree after assembly.

Its sleek and efficient design is optimized for fast 3D printing, taking only around 30 minutes to create. Whether you're looking for a thoughtful gift, a fun DIY project, or a unique addition to your holiday décor, the Christmas Tree Kit Card is perfect for spreading joy and creativity. Give it as a stocking stuffer, use it as a festive card alternative, or decorate your tree with these adorable baubles—there's no limit to the holiday cheer it can bring!

Single print fits on A1 Mini. P1, A1 and X1 will fit 2 cards on print beds.

IMPORTANT:

Please allow the print to cool down completely before removing it from the bed. Removing it too soon may result in warping of the card.

Assembly is straightforward:

Boost Me (for free)

Please boost this model if you like it :)

christmas tree kit card

Bill of Materials

Bambu Filaments

Bambu Green

A00-G6-1.75-1000-SPLFREE

× 1

Buy Now

Download BOM

Comment & Rating (55)

@felix_walch

Print Profile

0.2mm layer, 2 walls, 15% infill

Not printed beautifully

The designer has replied

Show original

@federnet

Did you try to calibrate flow rate for filament and skipped one zero when providing the result? This does not look like issue with a model, but an issue with a printer or some of the print parameters would be completely off :(

(Edited)

@felix_walch

Replying to @federnet :

the rest of my prints came out perfectly! but I’ll try again after a new calibration. thx

@federnet

Replying to @federnet :

Did you use the same filament for other prints?

@3dmudel.ee

Print Profile

0.2mm layer, 2 walls, 15% infill

success in 1st try

@Jordanw6

Print Profile

0.2mm layer, 2 walls, 15% infill

Overall, great print! Took roughly 30 minutes. On assembly, I recommend using scissors or ideally side snips. Additionally, be aware of the orientation of your 3 center support pieces. I recommend assembling them all with the same side up, as printer bed can effect the perceived texture. I used a texture bed and think the textured side looks best facing upwards, but you may think the opposite! In my photo, the top and bottom center pieces are print bed side up. the middle piece is the opposite.

@luke4288

Print Profile

0.2mm layer, 2 walls, 15% infill

Quick and easy, nice

@user_2066570333

Print Profile

0.2mm layer, 2 walls, 15% infill

@user_527938231

Print Profile

0.2mm layer, 2 walls, 15% infill

This was a good print. I little too simplistic for me, but I think that is the point here. Great design.

The designer has replied

@federnet

I have a design of a complex tree in progress now. Should be ready in next 4 days :)

@user_527938231

Replying to @federnet :

Looking forward to it.

@federnet

Here you go: https://makerworld.com/models/855213

@user_1722322982

too flimsy and parts can easily be ripped when pulling from the design.

The designer has replied

@federnet

As written in the description- just wait with taking the print off the plate until it cools down. Regarding flimsiness - I had to make compromise to allow quick print.

@matej.medvecky

Print Profile

0.2mm layer, 2 walls, 15% infill

great as gift

@DYSRDesign

Print Profile

0.2mm layer, 2 walls, 15% infill

need a bit of instructions

The designer has replied

@federnet

Did you check the model page? There is an animation with assembly view.

@user_1799072000

Print Profile

0.2mm layer, 2 walls, 15% infill

It's hard to get apart but fun idea.

The designer has replied

@federnet

Use small side cutters or scissors :)

(Edited)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(2)

Description

Bill of Materials

Comment & Rating (55)

License

Related Models

3D-printing in progress - Warning sign

mini hearts fast hollow print

Fast Food Dice

Paper clip style of the classic Microsoft Office