MagSafe iPhone and AirPods Pro Charging Stand by jaspauls

jaspauls

Hobby & DIY>Other Hobby & DIY

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.16mm layer, 2 walls, 15% infill

Designer

20 h

12 plates

4.4(16)

A1Mini, 0.16mm layer, 2 walls, 15% infill

23.1 h

12 plates

2.0(1)

Open in Bambu Studio

Boost

610

1095

575

201

Released

Description

MagSafe Holder for iPhone and AirPods Pro 2. Generation

This innovative iPhone Dock is specifically designed for various iPhone models and the AirPods Pro (2nd generation), as well as the MagSafe Charger and Apple Watch charger. The dock consists of three main components:

Frame with MagSafe Charging Function: The frame incorporates the MagSafe charger, securely holding and charging the iPhone. Cables are routed elegantly to the rear through specially designed channels.
Base with AirPods Pro Charging Station: The base allows for an Apple Watch charger to be pressed into the underside, enabling the AirPods Pro to be magnetically held and charged upon placement on the designated platform. This setup not only facilitates the magnetic alignment but also ensures efficient charging. Additionally, the base is designed to allow the frame to rotate, enabling flexible positioning.
End Caps: The end caps are pressed into the construction from the outside to securely fix the frame in place. Both the end caps and the base are equipped with grooves that allow for fine adjustment of the holder angle.

Assembly: To mount the holder, the MagSafe charger can be pressed into the designated recess in the frame. Before doing this, the cable should be routed through the cable channel to the back. The frame with the MagSafe charger can be inserted into the base and secured from the outside with the end caps. The Apple Watch charger should be pressed into the base from below.

Compatibility: The holder is specifically designed for various iPhone models, with and without cases, and for the AirPods Pro 2nd generation. It is produced in four sizes on different print plates. More detailed information about the compatible iPhone models, the associated print plates, and the internal dimensions can be found in the attached table.

Compatibility Note: Functionality has been confirmed with an iPhone 15, the latest MagSafe Charger, and Apple Watch charger, and is based on the dimensions provided by Apple. It should, therefore, be suitable for the models listed in the table. However, an adjustment may be required when using a very thick case. If compatibility issues arise, please leave a comment for adjustments.

Comment & Rating (48)

@phobic

GOD DAMNIT :D So many choices and no one fits.

The designer has replied

@jaspauls

Sorry to hear that. Which model are you using? If none of the models fit, please feel free to send me the exact dimensions of your smartphone with the case. I’ll be happy to create and publish a suitable model for you.

@phobic

Replying to @jaspauls :

The outer dimension are fine - it's a 15 Pro, its the back that is the problem. It's just my hardcore protection cover that has a hefty lens cover. I measured the square outside the lenses to be around 7.5mm offset out from all lenses - if you get me.

@jaspauls

Replying to @phobic :

Alright, I’ll see what I can do and will get back to you via direct message.

@DonSciazza84

Print Profile

0.16mm layer, 2 walls, 15% infill

Some issues with the interlocking caps

The designer has replied

Show original

@jaspauls

Sorry to hear that. Could you please describe your issues in more detail so I can make adjustments to the model if needed? Feel free to send me a private message.

@moaathe77

Print Profile

0.16mm layer, 2 walls, 15% infill

The product has good quality, the only issue is the joints don’t hold the angle well.

@marta286

Print Profile

0.16mm layer, 2 walls, 15% infill

It's a shame that the cameras protrude from the rather poor model

Show original

@user_919460481

Failed over and over again.. :(

@asunez

Boosted

Would it be possible for you to provide a version for iPhone 12/13 >mini< (they should be roughly the same size, there are only some minor changes to the camera bump as far as I know)?

The designer has replied

@jaspauls

I adjusted and published the stand for the iPhone 12/13 Mini. These can be found on print plates 9 and 10 for iPhones without a case, and on plates 11 and 12 for iPhones with a case. Have fun printing!

@asunez

Boosted

Replying to @jaspauls :

This is awesome, I’ll give it a go as soon as I get back home. Thanks a lot!

@user_4102644810

Brutal!!! I love the design, adding a hole to the base for Apple Watch charging would make it perfect

The designer has replied

Show original

@jaspauls

Thank you. Great idea.

@AngryPearl

Replying to @jaspauls :

Yees, my 2 boosts are waiting for version with apple watch charging :)

@asunez

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

I printed the 12/13 mini plate (with case), fits like a glove even with my not-so-thin silicone case. This is awesome, thanks for providing the adjusted profile with the 12/13 mini dimensions.

The designer has replied

@jaspauls

I’m glad you like it. You’re welcome!

@Balbertson

Boosted

Great design!

The designer has replied

@jaspauls

Tank you!

@MNM94

Boosted

I love this design!! though I printed for my 16 pro max without a case and it’s a little big all round. has anyone found another that fits better?

@MNM94

Boosted

any updates on this? I’d love to find if the frame fitter my phone a bit better! it would probably be fine if you use a case but I don’t.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

AirPod Pillow MagSafe

HpInvent

393

406

Minimal iPhone, AppleWatch Magsafe Stand

Print Profile(2)

Description

Comment & Rating (48)

License

Related Models

AirPod Pillow MagSafe

Minimal iPhone, AppleWatch Magsafe Stand

iPhone 13 Pro Case with MagSafe (TPU 95A)

Magsafe Stand for iPhones