AMS v2 riser drawer with customizable front plate

Remixed by

AMS v2 riser drawer with customizable front plate

Remixed by
Boost
37
128
20

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

V2 0.2mm layer, 2 walls, 15% infill
V2 0.2mm layer, 2 walls, 15% infill
Designer
5.6 h
1 plate
4.8(6)

Open in Bambu Studio
Boost
37
128
20
6
151
47
Released

Description

V3 is out now! Go check it out here The Toolbox AMS v2 riser drawer it is a complete overhaul set up to be the ultimate maintenance drawer!

 

A remix of a favorite AMS Riser drawer with multi color and you can attach any AMS riser drawer front plates. faceplates can be found on the AMS riser v2 page by maCyo42 link: AMS Riser V2 Remixed by maCyo42 - MakerWorld
 


 

 


 

Comment & Rating (20)

Please fill in your opinion
(0/5000)

Boosted
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
first week printing and it was flawless on my p1s. great design that fit like a glove. maybe printing front of drawer would reduce waste but I do not know enough to comment, grin thanks for project
The designer has replied
1
Reply
thank you for the review and boost! unfortunately multicolor printing does waste some filament. there are was to print the purge filament into the infill and other settings to reduce it a bit but sometimes you can see the bleed through on those depending on the color.
(Edited)
0
Reply
Boosted
Replying to @Bushwacker52 :
your hint on angling the wiper first was dead on. Fit like a glove …u da man
1
Reply
Such a waste of filament, constantly switching colors, it breaks my heart, though it’s perfect, still grateful for the wonderfully designed drawer
(Edited)
The designer has replied
Show original
0
Reply
Not to be mean, but load a single spool and set it to print single color. Problem solved. That's not much poop honestly though.
0
Reply
My deepest gratitude, your design is superb
Show original
0
Reply
just wanted to let you know I fixed this issue along with a list of other clearance issues that were brought to my attention the updated drawer is much better!
(Edited)
1
Reply
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
It's a good design; however, the slicing is flawed, producing incorrect layer lines during printing. Additionally, it generates unnecessary supports, hindering the two rails required for the drawer to fit, resulting in a very tight slide.
The designer has replied
Show original
0
Reply
thank you for the review. the supports on the bottom are to make sure the slots for the rails stay the right dimensions and the lamination could be the filament needing to be calibrated. sometimes that happens when it's under or over extruding from the nozzle
0
Reply
Replying to @Bushwacker52 :
Finally, you can easily remove them Thank you for your response
Show original
0
Reply
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
Wanted to match my risers color wise and also wanted to try something new. I did have to restart the print, but that was my error not the file. Once I corrected my mistake the print went smooth and looks great. Nice job!
1
Reply
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
really like how the assembled hot ends fit. might have to try your other version too
The designer has replied
1
Reply
thank you! the remix i used for this definitely grabbed ahold of them and id have to pull out the entire drawer to remove the assembled hotends and the wipers and cutters would also scrape the top. The toolbox version is more for if you want a one stop drawer for all the maintenance things. I prefer it over this one but i know some people prefer the extra storage spot on the side and that's why I kept this one up
(Edited)
0
Reply
Boosted
Great design. The wipers do not fit in slots and maybe make hothead slots a tad bigger. Thank you for your work
The designer has replied
0
Reply
If you put the wipers at an angle while you slide them in they side in much easier. there is a little divot on the front side to keep them secure and not wobbling around
0
Reply
I have updated the model to include the changes you have asked for the clearance issues with the nozzles, wipers, and cutters. I also cut print time in half as well as you can now put any riser faceplate that uses the hexagon attachment points
(Edited)
0
Reply
super tight fit sliding into the riser and parts like the filiment cutter, wiper, and hot ends scrape the top when sliding in, ultimately when back to an older drawer
The designer has replied
0
Reply
I just updated the model to fix those issues. I also made it a much easier print where it only swaps filament 8 times and can use any ams riser drawer faceplate with the hexagon attachment points. Thank you for pointing out those issues. I appreciate it and hope you like the updated drawer much better!
0
Reply
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
0
Reply
Boosted
Print Profile
V2 0.2mm layer, 2 walls, 15% infill
0
Reply
No more