Cozy Christmas Mushroom House Lamp

wuguigui
Household>Festivities
IP Report

Cozy Christmas Mushroom House Lamp

wuguigui
Boost
696
1412
110

Print Profile(1)

All
A1 mini
A1
Cozy Christmas Mushroom House Lamp
Cozy Christmas Mushroom House Lamp
Designer
19.2 h
8 plates
4.8(62)
Open in Bambu Studio
Boost
696
1412
110
112
914
275
Released

Description

This is a cozy Christmas mushroom house lamp remixed from my mushroom house lamp, including a cute snowman that can move its head around.

 

Disclaimer: This model is part of the Creator Program, When you purchase the hardware kit through the links below, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)

Recommended filaments: Bambu PLA Basic (Mistletoe Green) , Bambu PLA Basic (Jade White), Bambu PLA Matte(Ivory White), Bambu PLA Matte(Scarlet Red), Bambu PLA Matte(Mandarin Orange), Bambu PLA Matte(Dark Brown)

See how to assemble the house body

 

Download the LED Strip Christmas Tree

Watch the video for more information:

 

Merry Christmas! Makers!

Have fun!

 

lamp
mushroom
001
LED
LED 001
garden
decor
Christmas

Bill of Materials

Maker’s Supply Kits and Parts
MH001
13.00 USD
 × 1
B-CA001
2.19 USD
 × 1
Bambu Filaments
A00-G2-1.75-1000-SPLFREE
19.99 USD
 × 1
A01-W2-1.75-1000-SPLFREE
19.99 USD
 × 1
A01-R1-1.75-1000-SPLFREE
19.99 USD
 × 1
A01-N2-1.75-1000-SPLFREE
19.99 USD
 × 1
A01-A2-1.75-1000-SPLFREE
19.99 USD
 × 1
Buy Now
Download BOM

Comment & Rating (110)

(0/5000)
@Tumki
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
Everything worked well. The only issue I had were the stick arms and tree trunks not adhering to the plate. Which I solved by printing the arms slower and added a brim on the tree trunks.
1
Reply
@wuguigui
I think your hot bed plate might need to be replaced
0
Reply
@Tumki
Boosted
Replying to @wuguigui :
Could be, I’ve noticed bed adhesion near the edge of the plate is a bit less than near the center. Maybe the low ambient temperature in the room is at fault. I’m new to 3d printing, so I have to figure stuff out as I go along.
0
Reply
@wuguigui
Replying to @Tumki :
The plate has life, usually after half a years' use, the adhesion getting weak
1
Reply
@madkrom
Hello, the print stopped just before completion because the center of the piece rubbed against the nozzle I suspect insufficient infill What do you think
The designer has replied
Show original
0
Reply
@wuguigui
what happened? I don't have this issue when printing
0
Reply
@madkrom
Replying to @wuguigui :
The center of the piece didn't adhere to the infill, I believe, which caused a lifting of the piece and the nozzle to rub against it
Show original
0
Reply
@salpicom2016
Replying to @wuguigui :
i have problem too i think the problem is not have infill in all the stl file
1
Reply
@user_2884642736
it is like impossible to remove
The designer has replied
0
Reply
@wuguigui
just remove the big supports, keeping the rest is fine, it will not affect the light
0
Reply
@user_2884642736
Replying to @wuguigui :
how did you remove the big support
0
Reply
@wuguigui
Replying to @user_2884642736 :
Needle nose pliers! every 3D printer user has one
0
Reply
@jdub
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
Amazing design that printed great. It’s proudly displayed in our front hallway. white for snow areas = Bambu Lab Matte - Ivory White white for lamp body = eSun ePLA-HS - White red = eSun ePLA+HS - Fire Engine Red brown = Bambu Lab Pla Basic - Brown green = Bambu Lab PLA-CF - Matcha Green Orange = eSun ePLA+HS Orange
2
Reply
@wuguigui
Nice and detailed review, thank you!
0
Reply
@Xandie
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
glued down the trees before realizing I was supposed to print trunks... but like them without. ended up putting a little battery puck light inside. so cute! used a dual color (black/red) foe the doors and windows which made it pop soo much more! thinking th roof would have been super cool using the fuzzy feature....
2
Reply
@tomsmol3d
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
super
1
Reply
@bilal_emer
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
I created this model as a gift and I love it The creator's skill and effort are commendable Thank you
Show original
1
Reply
@sadfez
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
Love it!
1
Reply
@user_2848999144
Boosted
Print Profile
Cozy Christmas Mushroom House Lamp
Crafting this was fun and the result looks fantastic - many thanks 😊
Show original
1
Reply
@Miniunder
Print Profile
Cozy Christmas Mushroom House Lamp
Very beautiful. It prints perfectly. Perhaps I would add some type of support to the ceiling so that it closes without any marks, but it came out very well anyway
Show original
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Get Commercial License

Related Models

Mushroom House

Mushroom House

ThillyGooth
0
6
3
Mushroom Lamp N°3

Mushroom Lamp N°3

<ms/>
0
17
6
Mushroom Lamp N°2

Mushroom Lamp N°2

<ms/>
0
13
4
Mushroom Lamp N°1

Mushroom Lamp N°1

<ms/>
0
9
4
PrivacyTermsGuidelinesFAQCookie SettingsHot Searches
© 2025 MakerWorld