Breville Portafilter Hanger

Copyright Claim

Breville Portafilter Hanger

Boost
67
181
30

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 2 walls, 15% infill - With support
0.2mm layer, 2 walls, 15% infill - With support
Designer
1.5 h
1 plate
4.9(24)

Open in Bambu Studio
Boost
67
181
30
28
249
193
Released

Description

Portafilter Hanger for the Breville Barista Express (54mm)

 

I designed specifically for the Barista Express but it should work for other Breville machines

The fillets aren't a perfect match, but it's close enough to work great and not bad enough to make me want to redesign and reprint. With that said, I included the f3d file - feel free to remix!

 

I printed in PETG for heat resistance but I imagine PLA would work fine as well

 

I printed on it's side with support for the overhanging section

Comment & Rating (30)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Printed out of PETG-HF and it worked although slightly bubbly. Looks like a filament issue, wouldn’t fault PLA profile for this.
The designer has replied
1
Reply
Is the bubbly side where the supports were connected? I didn't spend any time fine-tuning the support settings, just went with default and it was good enough on my end not to tune and reprint. Could also just be wet filament though. I imagine most people already know about this but I just discovered the magic of using PLA for support on a PETG print or vice versa. Total game changer if you have an AMS!
1
Reply
Replying to @user_467481516 :
It's more like between the spots where supports connect. According to the forums there seems to be an issue with profiles for HF — they don't do so well even on short overhangs and bridges.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Printed in just over an hour using settings as-is on my P1S, in basic black Bambu Lab PLA. I don't expect any issues with the heat levels on the machine using PLA either but if anything crops up I'll add a new comment. Exactly what I was after!
The designer has replied
1
Reply
I like the matte black color of your machine!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
I like it a lot, except for the bit how it attaches to the machine I would really appreciate tighter fit. Printed in translucent gray petg, ended up with really nice texture. Will upload profile for this.
The designer has replied
0
Reply
Looks good! I was planning to make a version 2 with a better fit but I found this one hung on tight enough so I called it good
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Great print, works out perfect with my Sage Barista Expres. Printed with the recomende supports and turns out great.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
fits great on machine and handle.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Amazing! I absolutely love it!
Show original
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Great design. The only problem I have is when I take the portafilter off of it it usually falls off the machine. I think this is due to the ring on the handle of the porta filter hitting the bottom of the hanger.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
fits on the machine and holds the portafilter perfectly
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
Works great, no issues with weight or strength.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill - With support
also prints well with 08 mm 😊
Show original
0
Reply