(NEW) Print in place planetary gear by CloseEnoughMachineShop

CloseEnoughMachineShop

Education>Physics & Astronomy

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

1.7 h

1 plate

4.4(44)

Open in Bambu Studio

Boost

149

324

693

444

Released

Description

A simple print in place model of a planetary gear with dual helical gears.

Due to complaints that the gears could fall out, I have completely redesigned the model.
The new model has a steeper angle on the gears, as well as stronger ring gears to reduce the risk of the planet gear falling out. In addition, the model is smaller to fit more easily in the hand.

Print in place with my print profile.

If your using the stl-file. Remember to separate the objects before printing.

Boost Me (for free)

Thanks for the support!

Comment & Rating (55)

@EmRon

Print Profile

0.2mm layer, 2 walls, 15% infill

laid flat, works brilliantly. however given the tolerance and design width, the gears often bind when in any other orientation. still an excellent design, but doesn't get 100% wow for that reason

The designer has replied

@CEMS

New model available, it holds together much better

@DJJudah

Print Profile

0.2mm layer, 2 walls, 15% infill

Works great but it instantly stops spinning when you stop pushing it.

@user_1394191928

Print Profile

0.2mm layer, 2 walls, 15% infill

Excellent print quality and lots of fun and detail to explore.

@3DCrafts

Print Profile

0.2mm layer, 2 walls, 15% infill

perfect spins good

@fredjust

Print Profile

0.2mm layer, 2 walls, 15% infill

Other Issues:Not entirely satisfied, very difficult to unlock after printing (I almost broke it), it does not rotate freely afterwards, constant pushing is required Moreover, it can hurt your fingers when rotating it, the gears are very sharp

Show original

@user_2135019773

Print Profile

0.2mm layer, 2 walls, 15% infill

I made the mistake of printing 3 copies on the same plate without looking at the plate mock-up before printing, and all parts printed separately. I still haven't found a way to put it back together, due to the chevron shape of the cogs, but the second one was perfect.

The designer has replied

@CEMS

Ohh. Its important to ”print in place” on this one.

@user_2135019773

Replying to @CEMS :

I learned that lesson the hard way! Still, not a loss: I will find something to do with the spare cogs, or keep telling myself that I will, which is good enough.

@FrightGeist

Print Profile

0.2mm layer, 2 walls, 15% infill

@3Folm.yt

from the screen to the ring i wanna print this but gotta print Smith else

@3Folm.yt

say hello to my lil frien

@gajdude

Print Profile

0.2mm layer, 2 walls, 15% infill

too loose. gears skip a tooth and then it doesn’t turn. gears pop out too easily

The designer has replied

@CEMS

sorry to hear that. I have a new planetary gear designed. Will post it later

@CEMS

New model available, it holds together much better

@user_3748454832

Print Profile

0.2mm layer, 2 walls, 15% infill

lasted about 5 minutes

The designer has replied

@CEMS

New model available, it holds together much better

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.