Fishing Rod Holder by Shiba

Shiba

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

Designer

9.5 h

3 plates

5.0(44)

3mm wall - 0.2mm layer, 3 walls, 20% infill PETG

Designer

7.2 h

3 plates

5.0(10)

Open in Bambu Studio

Boost

332

688

770

438

Released

Description

Basic fishing rod holder. Can be wall (horizontal) or ceiling mounted with reels inplace. 2 configurations - either for 4 or 5 rods. This is a 3D printed version of a acrylic fabrication. My original design (a long time ago) was laser cut and with one heat bend.

fishing accesories

fishing

fishing rod holder

Comment & Rating (65)

@UglyTaco

Print Profile

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

I’ve gifted many of these. thanks!

@UglyTaco

Print Profile

3mm wall - 0.2mm layer, 3 walls, 20% infill PETG

I’m glad the creator read my comment and took action in rescuing the thickness of the material! Printed with PLA.

@user_3113365760

Boosted

Print Profile

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

just what I needed to hang those poles on the ceiling. now they aren’t wedged on the top shelf. love the print.

@Fin_Master300

Print Profile

3mm wall - 0.2mm layer, 3 walls, 20% infill PETG

good print

@ElStabbyTabby

Pretty good 👍

@Meatball_Jones

Print Profile

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

turned out great!

@user_2241690438

Boosted

Thank you again.

@user_2241690438

Boosted

Print Profile

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

Thanks for making this fishing pole rack, just what I needed.

@UglyTaco

Any chance you could make the model thinner? I measured the L section at 4.8mm. Would be great from them to be 2.5mm overall thickness

The designer has replied

@DaddyOhh

L section thickness is at 6mm. Rod holder originally was a made from 6mm acrylic and heat bent. I could have a version at 4.5mm or maybe 3mm at minimum but will increase chance of breakage. Not sure what's the intent of going down to 2.5 mm. Reduce material / print time? Working on a remix that gets attached with keyhole for a more streamlined look.

@UglyTaco

Thank you for the response, yes, reducing print time would be great! I have made a few and I think 3mm - 3.5mm thickness would be enough to hold them up since you have the upper support for them to be ceiling mounted. I’m willing to experiment and report back after you make the changes. Thanks again

@UglyTaco

I cut this in the slicer at 2mm and printed perfect. I will mount it and report. should have no issues as long as I pre drill the holes for mounting. Can I post a remix? This only takes 1.4 hours to print and 57.2g of filament

@ShaverFam

Boosted

Print Profile

6mm wall - 0.2mm layer, 3 walls, 20% infill No support.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(2)

Description

Comment & Rating (65)

License

Related Models

Fishing rod holder - wall mount

Rod Holder

Fishing Rod

Fishing rod hanger