SANTA HAT Vortex Thread Passthrough Fidget -Simple

Fin3dPrinting
Toys & Games>Other Toys & Games
Copyright Claim

SANTA HAT Vortex Thread Passthrough Fidget -Simple

Fin3dPrinting
Boost
367
761
110
GIF

Print Profile(2)

All
A1
P1S
P1P
X1 Carbon
X1E
X1
A1 mini
Switch by layer - AMS or NO AMS
Switch by layer - AMS or NO AMS
Designer
2.9 h
1 plate
4.9(57)
Added Fuzzy Skin - Bottom White Section
Added Fuzzy Skin - Bottom White Section
2.5 h
1 plate
4.8(5)
Open in Bambu Studio
Boost
367
761
110
88
947
582
Released

Description

This is my Santa hat Vortex thread model! The print profile is switching colors by layer so no ams needed

Boost Me (for free)

Boost me! Free for you, helps me!

Thanks!

if you want commercial license, please visit my patreon page below

Settings-

Supports- no

Brim- no

Infill- 15% gyroid

Good luck!!!!!

Support my shop at https://fin3dprinting.etsy.com

see my YouTube channel at https://www.youtube.com/channel/UCr6vlDZr5RTa7Ya1-jMhi8w

My Patreon Here (commercial use) https://patreon.com/Fin3dPrinting?utm_medium=unknown&utm_source=join_link&utm_campaign=creatorshare_creator&utm_content=copyLink

christmas
hat
santa
santa hat
christmas hat
santas hat
vortex thread
vortex
thread
impossible
passthrough
fun
illusion
north pole

Comment & Rating (110)

Please fill in your opinion
(0/5000)
level
@rtippenhauer
Boosted
Print Profile
Switch by layer - AMS or NO AMS
Print worked well, but the top of the hat is a little too thin to allow the right piece to flow together from the top down. Going from the bottom up works great.
The designer has replied
2
Reply
level
@Fin3dPrinting
okay thanks for the rating! I will try to fix that!
0
Reply
level
@rtippenhauer
Boosted
Replying to @Fin3dPrinting :
Leave me a comment if you get if updated, I'd love to print it again. I didn't have Red loaded, so I went with Purple.
0
Reply
level
@Fin3dPrinting
Replying to @rtippenhauer :
okay!
0
Reply
level
@bacon_meduna
Print Profile
Switch by layer - AMS or NO AMS
Great print but it printed with a purge tower where I didn't think it needed one. Maybe it was my setting. will update to 5 stars if my fault.
The designer has replied
1
Reply
level
@Fin3dPrinting
don’t know about that I will look
0
Reply
level
@Maxime_Labelle
Its a prime/cleaning tower, its always best to have one when color are switching for best result. i think this model deserve the 5 stars, you should also check the profile before launching the print to see if it fit your preference. :-)
0
Reply
level
@user_1253325159
I personally disabled the purge tower in Bambu Studio, and the print was successful
Show original
0
Reply
level
@user_2132129283
Boosted
Easy print, awsome result! Works well both ways. My nephews are getting one each for Christmas, and I can tell already that they'll love them 🎅
The designer has replied
1
Reply
level
@Fin3dPrinting
thanks for the review!
1
Reply
level
@Mr.Printer
Print Profile
Switch by layer - AMS or NO AMS
This thing is awesome my kids love it! I made a video. https://youtube.com/shorts/kVA4TkJe_fI?si=JHoVvboyrPSmiZQv
The designer has replied
1
Reply
level
@Fin3dPrinting
happy you like it!
0
Reply
level
@rggalvin
Boosted
Print Profile
Switch by layer - AMS or NO AMS
Came out great!
The designer has replied
1
Reply
level
@Fin3dPrinting
happy you like it!
0
Reply
level
@user_2509318016
Print Profile
Switch by layer - AMS or NO AMS
works well. gets a bit stuck in a few places but I'm sure after using it a lot they will wear out
The designer has replied
0
Reply
level
@Fin3dPrinting
happy you like it!
0
Reply
level
@Aldarion1
Printed great!
The designer has replied
0
Reply
level
@Fin3dPrinting
looks great!
0
Reply
level
@user_3921367047
Print Profile
Switch by layer - AMS or NO AMS
Awesome Model. Simple Print. Love it. Looks amazing in matte.
The designer has replied
0
Reply
level
@Fin3dPrinting
thanks!
0
Reply
level
@Jxer_Tnirp
Print Profile
Switch by layer - AMS or NO AMS
Can't get enough of these little guys.
The designer has replied
0
Reply
level
@Fin3dPrinting
happy you like it!
0
Reply
level
@user_1131959481
Print Profile
Switch by layer - AMS or NO AMS
great print!
The designer has replied
0
Reply
level
@Fin3dPrinting
looks great!
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Collapsable fidget Santa's hat

Collapsable fidget Santa's hat

romek142
101
908
2.9 k
Threaded Dragon Egg

Threaded Dragon Egg

steve_82
5
110
193
Big collapsable fidget Santa's Hat

Big collapsable fidget Santa's Hat

romek142
31
390
1 k
Pipe thread measure tool

Pipe thread measure tool

Martin
0
13
20
PrivacyTermsGuidelinesFAQCookie PolicyCookie SettingsHot Searches
© 2024 MakerWorld