AMS lite Anycubic Cardboard Spool Adapter

AMS lite Anycubic Cardboard Spool Adapter

Boost
38
95
22

Print Profile(1)

All
A1
P1S
P1P
X1 Carbon
X1E
X1
A1 mini

0.28mm layer, 2 walls, 15% infill
0.28mm layer, 2 walls, 15% infill
Designer
44 min
1 plate
4.7(18)

Open in Bambu Studio
Boost
38
95
22
15
200
147
Released

Description

This model allows for easy mount and dismount of Cardboard Anycubic spools on the AMS lite system. The rubber feet on the AMS lite cause high friction between it and the cardboard spool, making it very difficult to place the spool on the AMS and even harder to take it off.

That's why I designed this spool adapter which allows you to easily put your Anycubic cardboard spools on and off the AMS lite.


HOW TO USE:

You have to put the adapter through the spool before mounting it on the AMS lite system. If you notice, there are 3 cutouts on the end of the adapter. The flat side will be facing outwards, and the side with the cutouts will have to be facing the AMS lite. You need to approximately align the adapter cutouts with the 3 holding arms/grabbers of the AMS (don't worry, it's very easy). The AMS lite grabber will somewhat slot in (LOOK AT PICTURE WITH RED PAINTED ARROWS) and then you proceed to slide it entirely in making sure that in the end the rubber is in the space of the cutout. Try it a few times, you'll get used to it.

 

The internal dimensions of my roll are 55.86mm and the width (height) of the spool is 59.7mm.

The model has the exact dimensions of 55.71mm for the spool interior, and height of 61.26mm with the tiny lip at the end. (There is a picture with every dimension on it)

Comment & Rating (22)

Please fill in your opinion
(0/5000)

Print Profile
0.28mm layer, 2 walls, 15% infill
It adapts perfectly to Anycubic Carton spools
Show original
1
Reply
Boosted
Print Profile
0.28mm layer, 2 walls, 15% infill
Fast clean functional
Show original
0
Reply
Can you make one for elegoo (53-54mm). If you have some time over. Many thanks.
The designer has replied
0
Reply
I am really sorry, but I don't have an Elegoo spool and I would need one for precise measurements. However, you can use the same file and scale it down to 96% of it's original size (which would bring the adapter diameter from 55.71 to 53.5mm). Maybe print the first 2cm at first so you don't waste filament, and if it doesn't fit or it is too loose, slightly add or remove 0.1% from the number and try again. To adjust only the height of the adapter (for spool width) uncheck the "uniform scale" mark and change the Z axis scale slightly. I know it's a bit of a hustle but unfortunately I can't do it unless I have it in my hands or have access to the exact numbers. Definitely let me know if the new spool works for you!
(Edited)
0
Reply
https://makerworld.com/en/models/1091924 I made a Remix of Jack Maslov's design if you want to give it a try ;)
(Edited)
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
works great!
1
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
fit perfectly
1
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
Printed just fine, Have to a bit careful installing as it will crack.
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
Parfait
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
Other Issues:didnt fit at all
The designer has replied
0
Reply
I'm sorry for that. Could you show me what's wrong so I can improve the design?
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
0
Reply