Santa Hat Earrings/keychain by cameronjlong90

cameronjlong90

Fashion>Earrings

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

0.08mm layer, 2 walls, 15% infill .4mm nozzle

Designer

56 min

1 plate

4.7(6)

0.08mm layer, 2 walls, 15% infill .2mm nozzle

Designer

45 min

1 plate

3.4(5)

Open in Bambu Studio

Boost

143

271

288

178

Released

Description

Santa hat earrings that would also work well as a keychain. Please note there are two different profiles based on the nozzle size, one is designed for .4mm the other for .2mm. If you print the .2 nozzle print profile with a .4 nozzle the loop will not print so please make sure to use the correct profile.

santa hat

santa hat earrings

keychain

Comment & Rating (22)

@jsis

They printed fine, but there is no loop to make them either earrings or a keychain, and I did not realize that before I printed them. printed directly from the file.

The designer has replied

@cameronjlong90

Interesting, so the loop doesn't show up in the slicer at all once the file is opened? I tried downloading the file directly off of the site but it seems to be showing up for me.

@coolkidirish

Replying to @cameronjlong90 :

Just to jump in here, I had the same issue with a 0.4 nozzle. It showed on the Prepare screen but would disappear once sliced. If I change the setting to 0.2mm it shows when sliced so I'm guessing the loop might be too small for the 0.4mm nozzle.

@cameronjlong90

Replying to @coolkidirish :

ahh, interesting thanks for pointing that out. I’ll have to take a look at the loop size. Thanks again for passing along your observation, much appreciated!

@patrickfoerster

Boosted

Print Profile

0.08mm layer, 2 walls, 15% infill .4mm nozzle

Prints beautifully, the colors are opaque and the top eyelet is printed flawlessly with my 0.4 nozzle. Highly recommended.

The designer has replied

Show original

@cameronjlong90

thanks for taking the time to review the design!

@user_2999495586

it printed well but the black looks brown and thin.

@Uawflyer

Print Profile

0.08mm layer, 2 walls, 15% infill .2mm nozzle

they didn’t print with the loop for the earring part. had to add a hole to design

The designer has replied

@cameronjlong90

Please note there are two different print profiles, one for .2 nozzle the other for .4 nozzle. If you print the .2 nozzle print profile with the .4 nozzle it will print with no hole.

@JAMES87

Print Profile

0.08mm layer, 2 walls, 15% infill .4mm nozzle

A tad large but truly beautiful

Show original

@user_2659831365

Print Profile

0.08mm layer, 2 walls, 15% infill .4mm nozzle

Very cute!

@GirthQuake

Print Profile

0.08mm layer, 2 walls, 15% infill .2mm nozzle

This is a good clean print. They were too big for earrings in my opinion.

@user_3780129664

no ring at top

The designer has replied

@cameronjlong90

There are two print profiles, one is meant for .2 nozzle the other for .4 nozzle. If you use the .2 model with a .4 nozzle no ring will print.

@user_984053825

Print Profile

0.08mm layer, 2 walls, 15% infill .2mm nozzle

the little ring at the top did not print....

The designer has replied

@cameronjlong90

there was a new print profile loaded, please retry with the .4mm nozzle profile. if you use the .2 model with a .4 nozzle it wont print the ring.

(Edited)

@ChrisConnor

Print Profile

0.08mm layer, 2 walls, 15% infill .4mm nozzle

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.