Bambu P1S Build Plate Aligner that Snaps intoPlace by The Grumpy Printer

The Grumpy Printer

3D Printer>3D Printer Accessories

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

13 min

1 plate

4.8(134)

Open in Bambu Studio

Boost

306

816

154

848

692

Released

Description

This is a Bambu build plate aligner – a convenient accessory that ensures perfect alignment of your build plate every time. It requires no assembly or extra parts; simply snap it into place, and it's ready to go. If you own a Bambu X1C, I'd love to hear how it works for you!

Comment & Rating (154)

@jpp123

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed cleanly and fits my X1C. First print was a PLA test. I plan to reprint in ASA or Nylon becasue I don't think PLA will work well with higher bed temps.

The designer has replied

@3print360

thank you

@jpp123

OK problem - I reprinted in ASA and the print head is just clipping the guide causing a layer shift after the 1st layer. I think the PLA one was also doing it but the head was hot enough to melt it a bit to soften the impact. I'm recalibraing the printer and will test again with a trimmed down ASA aligner.

@jpp123

Replying to @jpp123 :

Yep it's too hight, trimmed about 1mm off withe flushcutter and it works fine now :-)

@LinxAwakening

Print Profile

0.2mm layer, 2 walls, 15% infill

Easy, quick print that does exactly what it says it does. Makes sliding the plate in correctly so easy. Printed in PETG.

The designer has replied

@3print360

Thanks!

@user_1635299518

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

Can confirm: Works on P1S. Great little time saver! Thanks!

@user_1635299518

Boosted

PETG & P1S: The nozzle does clip the top of the guide. I pulled it out and there's some little scuff marks on the iop of left guide. Trimmed it with flush cutter.

@Ferzhul

On my X1C, the nozzle hits the build plate during cleaning after the first layer.

Show original

@jpp123

Mine too - I trimmed it down withe flushcutters in the end.

@LiAn1992

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed very well No particular irregularities Thank you

Show original

@DanieleOneda

Print Profile

0.2mm layer, 2 walls, 15% infill

very good

@user_3136758772

Print Profile

0.2mm layer, 2 walls, 15% infill

very good quality

@Laurent37FR

Print Profile

0.2mm layer, 2 walls, 15% infill

Very practical! Lightweight, uses little filament yet remains highly effective. Here, printed in Elegoo's Rapid PETG Gray. Thank you!

Show original

@user_701178871

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

Very helpful, easy print.

@jcor65

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

Splendid.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.