EZ-Lock Insert for Honeycomb Storage Wall by Wile E. 3D

Wile E. 3D

Household>Other House Models

IP Report

GIF

Print Profile(5)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

All The Parts On One Plate

Designer

48 min

1 plate

4.9(85)

Ten EZ-Lock Inserts

Designer

1.1 h

1 plate

5.0(31)

Snugger Fit EZ-Lock Insert

Designer

12 min

1 plate

5.0(4)

Allen Wrench Style Installation Tool and Holder

Designer

33 min

1 plate

4.5(4)

Click to see more

Open in Bambu Studio

Boost

315

1035

178

894

547

Released

Description

Boost Me (for free)

Are you like me and find yourself fighting with HSW inserts whenever you want to reorganize? I finally decided to do something to make it easy. Here is an easy to install and remove insert for the honeycomb storage wall. Just place the insert in the opening and use the provided tool to twist the insert until its aligned. I'm now including a profile for an allen wrench style tool that I prefer to use. Check out my other EZ-Lock models: https://makerworld.com/en/collections/2905373

Comment & Rating (178)

@Locutus

Print Profile

All The Parts On One Plate

The inserts are a little loose fit on your P1S wall. Make sure and clean up the support connection site for the holder, the tool fits perfect afterwards. Does make for EASY layout changes!

@gary.oldefendt

Can I ask if you printed with PLA? I've discovered the inserts and panels can wear after a few uses and get looser with PLA. I've switch to using PETG and have seen an improvement.

@Locutus

Replying to @gary.oldefendt :

I did print with PLA, they were loose for first insert. It’s not anything major, I’m using them on the P1S wall and don’t plan on changung much once setup

@gary.oldefendt

Replying to @Locutus :

OK, thanks. I know they were a good fit when I firstbstartedbusing them. I'll probably print a couple of PLA myself to see what results I get now.

@jonl123

Boosted

These are nice! I added a small ridge to the tool to prevent it from going too deep into the inserts. Can't post it due to the license, but it works well. I'd recommend adding this to the tool.

The designer has replied

@gary.oldefendt

The ridge is a good idea. I already have something like that on the Allen wrench style tool. Check out that profile.

@jonl123

Boosted

Replying to @gary.oldefendt :

Ah yes. After I added the ridge to mine I realized I should have instead made the insert end just a touch smaller instead. I didn't see that you had a snug version until now, glad to see that's there, printing a few now to test with. Thanks again!

@mister_scott

Boosted

I've remixed your design along witha tilt storage box (elongating the shaft of the insert to clear the wall of the box to secure it directly to the panel). Can I have your permission to post the elongated inserts and tools so others can enjoy it too? I'm requesting permission for reposting of the box from it's designer as well.

@mister_scott

Boosted

In case you're against a repost by others, can I send you the modified design so you can post it? I just want to get it into the community. :)

@user_37857779

Brilliant ! Fits very well. The Plug Tool Holder is a bbit to loose but I guess I took the "loose" version. I cannot find the other one. Anyway big thanks. It offers plenty of easier possibilities.

The designer has replied

@gary.oldefendt

Thanks! Ive now added a profile for an allen wrench style tool and holder that I've been including with some other models. I like it better than the original tool that I started with here.

@Rogger

Print Profile

All The Parts On One Plate

The system performs well I will print more hexagons for more intensive testing

Show original

@Adolamin

Print Profile

Ten EZ-Lock Inserts

love these! super easy to print thank you

@djensen623

Boosted

Print Profile

All The Parts On One Plate

Great model and perfect print. Thank you.

@bdepietro

Print Profile

All The Parts On One Plate

printed a handful of adapters and the tool with inland petg+, generic petg profile on x1c except nozzle set to 260 with recently dried filament. no issues at all, perfect fitment and works great for installed shelving. adapters hid perfectly behind shelving too

@mcginnis83

Print Profile

All The Parts On One Plate

They fit perfectly into the HSW Printed in Nebula Orange

Show original

@mcginnis83

Print Profile

Allen Wrench Style Installation Tool and Holder

Quick and easy print. Fits perfectly. Printed in Nebula Orange.

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Diamondplate Bin For Honeycomb Storage Wall

Print Profile(5)

Description

Comment & Rating (178)

License

Related Models

Diamondplate Bin For Honeycomb Storage Wall

Monopoly Junior Insert Storage

Twist lock container

Cyberion Insert