eSun Cardboard Spool - Hex Pattern Reuseable Spool

Remixed by

eSun Cardboard Spool - Hex Pattern Reuseable Spool

Remixed by
Boost
51
132
19

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
6.1 h
2 plates
4.9(12)

Open in Bambu Studio
Boost
51
132
19
16
144
89
Released

Description

Some recently bought eSun cardboard spools (PLA+/ePLA) could not be used on a Bambu Labs reuseable spool

(if you remove the cardboard walls), first I had to glue the sides together again. But after one fall off I had
to search for a other solution.
I created a spool with following parameters:

  • spool diameter: 200mm
  • spool core diameter: 75.7mm
  • spool hole diameter: 55mm
  • spool core width: 58.2mm
  • spool side thickness: 2.4mm.
  • applied some holes to save material

I applied a 10mm honeycomb cutout pattern.

If fits perfectly into the Bambu AMS.
If you print it with PLA, do not use the spool in a filament dryer .. it will deform.
If drying is a topic then print it in ABS. But I did not get spools from eSun except PLA/ePLA,
which need no dryer anyway.

Please also have a look on the Filament Clip (spring loaded) for Bambu Spool that fits this spool
or another kind of filament clip that I created Filament Clip for Bambu reuseable spool. Both fit
to this spool.
 

Boost Me (for free)

If you like the model, please boost this model.
Thank you very much!

Comment & Rating (19)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 4 walls, 15% infill
Excellent, PETG HF. Do not use reusable filament PLA+ from esun
The designer has replied
Show original
0
Reply
The picture might be the wrong one?
0
Reply
Sure it does not fit, this is for recent cardboard spools, which are smaller. You eSun refil spool fits on the Bambu reusesble spool. https://makerworld.com/de/models/719390?from=search#profileId-650206
1
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
Printed great in ASA!
The designer has replied
0
Reply
Which ASA did you use? I printed a Bambu spool with same hex pattern in QIDI TECH ASA grey which printed also flawless.
0
Reply
Replying to @user_859760970 :
I used Eryone standard ASA
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
printed fine in petg on x1c.
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
Printed in PETG, fits perfectly
Show original
2
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
printed well
The designer has replied
1
Reply
Thank you!
0
Reply
Ran into the same issue. Glad you created this solution
2
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
fits great
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
The designer has replied
0
Reply
Thank you for youre feedback. Anything you like to share to improve the model?
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply