Ikea lack leg riser

Ikea lack leg riser

Boost
43
144
14

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
17.7 h
1 plate
4.7(6)

Open in Bambu Studio
Boost
43
144
14
4
110
34
Released

Description

Boost Me (for free)

I hope that you liked the model and it was useful for you.
If you liked. your boost is highly appreciated.
Thanks

Ikea Lack Leg riser, low profile.
It rises the table 12 cm, space enough to accomodate a BambuLab A1 mini below.
I wanted a real sturdy Ikea lack riser and all the models I found where either quite high profile with external reinforcements or quite wobbly. The problem is that all of them use screws on the board part out of the leg, that is cardboard or even thin air. 
This design is quite sturdy.

Each piece is firmly attached with 4 screws to the part of the board that is chipboard made, where the main screw for the leg is originally attached, so is as firm as the original one.
The screws are hidden inside de piece.
The other side of the piece is screwed with the original Ikea screw to each leg.

-It is very recommended to mark the place where the screws will insert in the board with a pencil or with a little bit or talk powder or something similar through the holes, and make a small drill 2 mm to easy the screw insert in the board, otherwise it may expand too much and break the board panels when you screw the screws.

 

You will need a screwdriver of at least 15 cm as you have to tighten the screws through the printed piece (12cm)

 

Parts needed:

-16 countersunk self tapping screws 4x35 mm.

-15 cm screwdriver.
 

Bill of Materials

List other parts
  • countersunk self tapping screws 4x35 x 16

Download BOM

Comment & Rating (14)

Please fill in your opinion
(0/5000)

Which screwdriver did you use to screw in the screws? Because none of the ones I have fit
The designer has replied
Show original
0
Reply
I used a 15 cm normal screwdriver, but I will leave a note in the description.
0
Reply
Replying to @Peristro :
I had to cut off the handle of a screwdriver hahahaha
Show original
0
Reply
Replying to @P3R31R4 :
Hahaha I hope that it worked
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
17 hours!?? this looks fantastic as a sturdy placement for the printer, but Rather than waste time and filiment, i'm just going to buy some 5 by 5 wood and cut the 15cm myself.
The designer has replied
1
Reply
It is a great idea, I wish we could print the wood block.
1
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
The risers were a little bigger then the width of the ikea lack legs. In the pictures the legs showed that they were flush with risers.
The designer has replied
0
Reply
The pieces i printed are flush with my Ikea pack legs. Exactly, how much bigger are than your legs? You can measure the width yoursef in your slicer before print and even scale it if your legs are sligthtly smaller
(Edited)
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
0
Reply
No more