FAST and Strong Painter's Pyramids

Copyright Claim

FAST and Strong Painter's Pyramids

Boost
163
471
54

Print Profile(3)

All
A1
P1S
P1P
X1 Carbon
X1E
X1
A1 mini

0.28mm layer, 1 walls, 0% infill
0.28mm layer, 1 walls, 0% infill
Designer
1.2 h
1 plate
4.9(44)

A1mini original 0.28mm layer, 1 walls, 0% infill
A1mini original 0.28mm layer, 1 walls, 0% infill
47 min
2 plates
5.0(2)

Double wall (strong), 0.28mm layer, 0% infill
Double wall (strong), 0.28mm layer, 0% infill
1.7 h
1 plate
5.0(1)

Open in Bambu Studio
Boost
163
471
54
44
603
465
Released

Description

These are simple paint pyramids that elevate the piece you're painting so you can paint all sides at once, without waiting for it to dry.

This model is designed to be used with the Spiralize feature. When spiralized, they are still very strong, and stackable, and should only take a few minutes each to print. However, the print profile that I've included does not use the Spiralize feature; instead, it sets wall layers to 0 and removes the bottom. This lets you print 16 pyramids at once in about an hour.

 

I've also added 3-sided tripods and "tall" versions. The 3-sided tripods save a tiny bit of print time for similar strength. I am using the tall versions to paint a piece above a drying piece.


Print Settings:

Print with the Spiralize setting OR wall thickness set to 0 with no infill. Set the bottom layers to 0 to make them stackable. For a faster print, increase print speed but keep the initial layer speed lower to ensure adhesion. You may also want to decrease your "Minimum Layer Time" to about 2 seconds so that the upper layers don't slow down too much (this isn't an issue when you print a full plate).

Comment & Rating (54)

Please fill in your opinion
(0/5000)

Print Profile
Double wall (strong), 0.28mm layer, 0% infill
Takes longer than the 1 layer profile, but is totally worth it in my opinion!
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
the print worked finde, u used it for my small remains of filament
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
I've test-printed a few and they exhibit exceptional stability I'll now make a few more
Show original
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
Quick, easy, perfect
Show original
0
Reply
I've used these painter's pyramids for months now and like them so much I actually created a storage rack for them: https://makerworld.com/en/models/1023192#profileId-1004961
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
Quick print for how many I get, thanks for sharing.
0
Reply
Boosted
Print Profile
0.28mm layer, 1 walls, 0% infill
I don’t know what happened with those two, so I canceled them, but the others are perfect. I like that they are stackable!
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
0
Reply
Print Profile
0.28mm layer, 1 walls, 0% infill
A few of the 16 had some defects (printed with PETG), but otherwise nice model and very effective! I will try the 2 wall Version next time to compare.
0
Reply
Print Profile
A1mini original 0.28mm layer, 1 walls, 0% infill
light weight but sturdy. Only problem I had they stick to the underside of a wet surface although the mark they leave is very small and difficult to see. Stack nicely.
0
Reply