iPhone Standby Mode Dock for iPhone 13 mini

Remixed by
Copyright Claim

iPhone Standby Mode Dock for iPhone 13 mini

Remixed by
Boost
155
325
47

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
5.2 h
1 plate
4.8(32)

Open in Bambu Studio
Boost
155
325
47
45
842
311
Released

Description

.16mm layer height, 10% infill (i used gyroid), and supports for the large overhangs. Printed with white ELEGOO PLA Pro

I scaled everything down, then modified the frame to fit my 13 mini (a little space on the sides so the buttons aren't pressed down). I had to increase the size of the magsafe charger so it would fit, along with the tunnel for the apple watch charger. Everything's nice and snug, I'm using a usb c 6mm apple watch charger. This should fit the 12 mini as well, but the 13's just a smidge thicker. 

Comment & Rating (47)

Please fill in your opinion
(0/5000)

Print Profile
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
came out perfect, printed with Bambu pla matte
0
Reply
My iPhone 13 Mini fits well and snug, and I sticked 2 strips of electrician's adhesive tape on the charger to tighten otherwise it will be a little bit loosen when I take the iPhone off the dock. PS: I use 1st gen magsafe charger, it would be better if the cable hole of the docker could be a little bit larger cause the type-c head almost being stopped through it (I am not sure if the new-gen charger's type-c head will be smaller than the 1st gen). Thanks man.
0
Reply
Thank you for the model. It’s perfect!
0
Reply
Boosted
Printed great for iPhone 12 mini - adjusted for apple watch. Profile: https://makerworld.com/en/models/686334#profileId-614986
(Edited)
0
Reply
Print Profile
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
Print successful. Thanks. Print with PLA
Show original
0
Reply
Boosted
Print Profile
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
0
Reply
Just printed this, with bambu pla basic white. Printed nicely with settings recommended in the description, support tree was easy to remove. It fits an iphone 13 mini and 12 mini just fine. There was a tiny issue with the "push button" got stuck but after cleaning and sanding the slot it fits into it works as intended. The biggest issue, but this a general complaint about this model and not this remix, is that it your phone wont fit with a cover on, even a slim one. My phones have a thin rubber cover with bumpers on the four corners, and wont fit at all. So in the end, this print is useless to me sadly, because I dont want to remove the cover each and every time.
1
Reply
how did you remove the supports? mine are like stuck inside
The designer has replied
0
Reply
I used tree supports, getting a good grip and yanking had them separate fine. If they're stuck in the apple watch slot, I'm not quite sure, I blocked supports from being build over top of that area. You might try with a firm right angle tool to poke around in there to get it to crumble apart.
0
Reply
Boosted
Print Profile
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
Works great
0
Reply
Print Profile
[13 Mini, Tree Supp]: 0.2mm layer, 2 walls, 10% infill
It suits,OK
0
Reply