Sphere Impossible Passthrough by ATRO

ATRO

Toys & Games>Other Toys & Games

GIF

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 15% infill

Designer

1 h

2 plates

3.9(86)

Open in Bambu Studio

Boost

213

357

1.1 k

790

Released

Description

NO AMS NEEDED

Printed in two parts

No supports needed

If your printer prints it too tight then try making the X-Y contour compensation either -0.4, -0.45 or-0.5

无需 AMS

分两部分打印

无需支撑

如果您的打印机打印得太紧，请尝试将 X-Y 轮廓补偿设置为 -0.4、-0.45 或 -0.5

Boost Me (for free)

Boost if you like it!
喜欢就加分吧！

impossible passthrough

impossible passthrough sphere

impossible passthrough fidget

fidget

fidget accessories

fidget accessory

fidget impossible passthrough

Comment & Rating (93)

@alexschw1111

Print Profile

0.2mm layer, 2 walls, 15% infill

The spheres do not connect together, as the sizing is wrong. They only connect half-way and are stuck in, I have to throw this away. The creator should adjust the sizes accordingly.

@GTank35

Print Profile

0.2mm layer, 2 walls, 15% infill

my support may have come off wrong but it dosin’t appear to be causing issues

@user_563388560

Print Profile

0.2mm layer, 2 walls, 15% infill

Smaller then I thought it was, but so far so good

@mvachon8706

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

print ok

@Fredster

Print Profile

0.2mm layer, 2 walls, 15% infill

dont fit properly

@user_2609160200

Print Profile

0.2mm layer, 2 walls, 15% infill

Looks good, but it's a bit difficult to take apart with large fingers

Show original

@URCI_1830038132

Print Profile

0.2mm layer, 2 walls, 15% infill

Imprimé en PLA gris mat de Jayo et PLA Glow in the Dark d'Eryone. Partie inférieure un peu fragile.

@Tenty

Print Profile

0.2mm layer, 2 walls, 15% infill

Other Issues:Some of my prints fell apart for the outer shell. I finally found that I had to print them with no supports and using a cool plate. But the trial and error was time consuming. Also the spheres don’t actually pass through completely. They do lock together though. So they do make a complete sphere-ish shape (as best you can get for printing on a flat surface anyway)

@user_165123487

Print Profile

0.2mm layer, 2 walls, 15% infill

Strength Issue:it broke real easy if it didn’t break so easy it would be better

@Felipe24llaguno

Print Profile

0.2mm layer, 2 walls, 15% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Pendant Lamp Shade | 15cm Sphere, Checkerboard

Print Profile(1)

Description

Comment & Rating (93)

License

Related Models

Pendant Lamp Shade | 15cm Sphere, Checkerboard

Infinity Sphere Loop

sphere

Not Impossible Passthrough