Garden water sprinkler

Copyright Claim

Garden water sprinkler

Boost
344
609
51

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

PLA 0.16mm layer, 3 walls, 15% infill
PLA 0.16mm layer, 3 walls, 15% infill
Designer
5.6 h
4 plates
4.4(25)

ABS GF 0.16mm layer, 3 walls, 15% infill
ABS GF 0.16mm layer, 3 walls, 15% infill
Designer
8 h
4 plates
4.0(5)

PETG, no skirt, Brim where needed, A1 mini, 0.16mm, 3w & 15%
PETG, no skirt, Brim where needed, A1 mini, 0.16mm, 3w & 15%
7.5 h
4 plates
4.5(2)

Open in Bambu Studio
Boost
344
609
51
32
548
217
Released

Description

Boost Me (for free)

If you enjoy this model, Don't forget to boost the model :)

Description :

  • material - ABS GF
  • layer height  0,16  / 0,4 mm
  • thread G 3/4
  • 2 replaceable heads
  • adjust the water flow by releasing or reaching the head
  • 2 x plugs G3/4
  • use teflon tape for sealing

 

 

 

Comment & Rating (51)

Please fill in your opinion
(0/5000)

I like the idea but the thread is so tight that I couldn't get it screwed all the way andI broke it while assembling. The result is a fountain of less than 1 meter wide. Need to see if I can get it out and add 0.2mm more tolerance on the thread.
The designer has replied
2
Reply
the tolerance is quite large, try to reduce the material extrusion from 1 to 0.95
0
Reply
Replying to @RoBeRt16 :
I see you did made it from ABS, I made it from PETG which I think shrinks less. This could explain the difference
0
Reply
The thread is not GHT (garden hose thread). It makes little sense to have a sprinkler intended for garden hose application but not use GHT. I asked the designer to change the thread, but no response. Get an adapter G3/4 to GHT.
(Edited)
1
Reply
Print Profile
PETG, no skirt, Brim where needed, A1 mini, 0.16mm, 3w & 15%
Nice idea but quality of threads is not good
2
Reply
Print Profile
PLA 0.16mm layer, 3 walls, 15% infill
Design Top... the spray image is not very big. Maybe you can improve it with an update
Show original
0
Reply
Design is great; thread clearances are not.
2
Reply
Print Profile
PLA 0.16mm layer, 3 walls, 15% infill
its a nice model but does not work with garden hose thread.
2
Reply
canni pront this in a dofferent material like PETG?
The designer has replied
1
Reply
yes
0
Reply
Print Profile
PLA 0.16mm layer, 3 walls, 15% infill
The thread caps can be adjusted to fit better. Other than that, it works fine.
1
Reply
same bad threads great concept though!! keep it up!!
1
Reply
Boosted
Had to make an adapter to bring this pipe thread to a GHT 3/4 inch thread with a pitch of 15 (ANSI B1.20.7 for Fusion 360 thread library) and room for gasket inserts to help with leaks before the head. Functions as intended at around 30 PSI gives about 14 feet spray distance, but with no deflector, much of the interior of the coverage area is left dry. Put into the center of an array of planters this could be an advantage for proper use cases, like a greenhouse suspended above plants for instance.
(Edited)
1
Reply
Could you please redesign this model with standard U.S. garden hose thread?
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.