Spool adapter for SUNLU 250g with diameter 42mm

Spool adapter for SUNLU 250g with diameter 42mm

Boost
11
17
14

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
Designer
3 h
2 plates
5.0(6)

Open in Bambu Studio
Boost
11
17
14
12
62
50
Released

Description

Adapter for 250g SUNLU spools with an inner diameter of 42mm. Considered 15% infill but with 3 walls to make it rigid. The two pins have the anti-rotational function, locking the two pieces with the pins in the side holes of the spools remain fixed to the spool.
M20 screw locks in place of the two parts.
No support needed.

Any suggestions are welcome for improving the design.
If you want to make changes you are free to do so, but please mention this project.

If you found my project useful, please LIKE it and leave a review (and maybe a boost). Thank you.

 

Adattatore per bobine SUNLU da 250g con diametro interno di 42mm. Considerato riempimento al 15% ma con 3 walls per renderlo rigido. Le due spine hanno la funzione anti-rotazionale, bloccando i due pezzi con le spine nei fori laterali delle bobine rimangono solidali al rocchetto.
La vite M20 blocca in posizione del due parti.
Nessun supporto necessario.

Accetto suggerimenti per migliorare il design.
Se volete apportare modifiche siete liberi di farlo, ma per favore citate questo progetto.

Se il mio progetto ti è sembrato utile, per favore metti LIKE e lascia una recensione (e magari un boost). Grazie.

Comment & Rating (14)

Please fill in your opinion
(0/5000)

is the screw supposed to connect to the second part of the holder? it doesn’t seem to hold my spool in place.
The designer has replied
0
Reply
Is the spool SUNLU? The pins protruding on the two sides are to be inserted into the holes on the side of the spool, the screw tightens everything and locks the rotation between the spool and the adapter. I have designed this system for SUNLU 250g PLA+ spools.
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Everything is perfect, I just have one tip: If you're still drying the filament, don't print the spools out of PLA, they'll warp, which is pretty much a silly beginner's mistake I made. The model and the print file are flawless and highly recommended!
The designer has replied
Show original
0
Reply
Thank you very much for your rating and your comment.
0
Reply
What printer is this spool for? I assumed (incorrectly) that it as for the Bambu A1/A1-mini and AMS Lite. The print was great but turned out not what I needed.
The designer has replied
0
Reply
Thank you for your comment. Yes, I confirm that it is for AMS and not AMS lite.
1
Reply
Excellent design...does the job
The designer has replied
0
Reply
Thank you, your comment is much appreciated. I’m glad I was helpful.
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
The designer has replied
0
Reply
Thank you!
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
No more