Syringe (Fully 3D Printed)

Copyright Claim

Syringe (Fully 3D Printed)

Boost
110
199
38

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

Ironing - 0.2mm layer, 2 walls, 25% infill
Ironing - 0.2mm layer, 2 walls, 25% infill
Designer
37 min
1 plate
4.3(29)

Modified version, 2 colors, print by object, TPU tip
Modified version, 2 colors, print by object, TPU tip
1.6 h
2 plates
5.0(2)

Open in Bambu Studio
Boost
110
199
38
19
560
408
Released

Description

Introduction

A simple small, fully 3D Printed syringe for viscous materials. As the seal between the parts is not 100% tight, it is recommended to not use liquid materials. Possible use-cases are e.g. Epoxy Resin, Silicone, Liquid soap (may be to thin)…

 

Materials

  • Filament: Any (Hard) - PLA, PETG, ABS, ASA, …

Boost Me (for free)

:]


Setup

  1. Choose Color
  2. Print
  3. Fill the syringe with the material
  4. Insert the Plunger
  5. Done! Apply force to press out material

Let me know if there is anything to change! Have fun with it :)

Comment & Rating (38)

Please fill in your opinion
(0/5000)

Boosted
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
In general design and printability is good. But unfortunately syringe doesn't work and can't take any water or any low density liquid. Also I didn't like that syringe is not easy to open because of unsufficient handle. So, I added TPU end and extend handle now it work as it should.
The designer has replied
0
Reply
Hi, thanks for your reply :) As said in the description of the syringe, it is not 100% tight and therefore isn’t intended for water or other materials of low viscosity. But with all the feedback, i will soon release a second version.
0
Reply
Boosted
haha, so I'm sorry I didn't read it 🫣 Then my rating is 5* 😀
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
Printed without issues 👍
Show original
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
printed fine but doesn’t work very well
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
0
Reply
Boosted
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
This actually worked. I did print a TPU plunger end that made the syringe more air tight. Used to inject rubber into a mold and it worked like a champ! Thank you!
The designer has replied
1
Reply
thanks! great idea to use a TPU plunger tip! If you want, you are welcome to share your print profile :)
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
good prop but doesnt work at all
The designer has replied
0
Reply
what is the problem? what do you want to use it for? as i said in the description, it is not suitable for thin liquids like water
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
Only decorative. Can't use it
The designer has replied
0
Reply
what was the issue? as i mentioned, it is only for viscous substances like glue. it doesn’t seal very well as it is printed, therefore cannot be used with water
0
Reply
Print Profile
Ironing - 0.2mm layer, 2 walls, 25% infill
I needed a quick epoxy applicator to set magnets. This model worked perfectly. Thanks!
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.