A1 Toolbox All in one by mrhansen7692

mrhansen7692

3D Printer>3D Printer Accessories

Print Profile(1)

All

0.2mm layer, 3 walls, 15% infill

Designer

9.3 h

2 plates

4.9(58)

Open in Bambu Studio

Boost

150

338

480

301

Released

Description

Yep, just another tool box more my style! just a perfect all around fit.

Holds:

4 hotends
4 filament cutters
2 silicon socks
both lube bottles
2 scrappers
2 nozzle clog tools
both of the hex tools
extra scrubber pads and various othe bits and bobs

https://www.printables.com/model/258431-rugged-box-parametric/files '

the box is from this link * i only made trays, added text to the lid, and edited the box to have floating trays. Also changed the measurements of the original box. Enjoy!! I advise not tipping it or adding thick foam to the top to keep everything in place. :)

Need either 6 M3x30 Screws, or 6 M3x35mm screws and 6 nylock nuts either or.

Comment & Rating (94)

@user_399283293

The inserts and bottom of the box printed well. But I'm having trouble printing the lid. Not sure really why, but it's failed 4 times over a couple of days. Have also tried just using a single filament but still no luck. Now I'm really keen to have a simple version of this without the lettering and logo. Scaling the original (thanks for linking to the source) is my next trick. Would love to know any scaling or which of the original sizes was adapted for this - just make sure I follow the steps correctly to match the bottom of the box.

The designer has replied

@mrhansen7692

Try them separate, also i clean my bed on my printer with dawn dish soap and hot water Every couple days. It appears that yours might have something causing it on that side alone.

@user_399283293

Replying to @mrhansen7692 :

Thank you for these suggestions. I had done exactly those things after the first fail (which is shown in the pic). I've also slowed down the first layer speed to about 40. Subsequent efforts have failed earlier than this when trying to put down the first very small edges of the lettering and logo.

@mrhansen7692

Replying to @user_399283293 :

Hmm Sorry for the issues this happens to be the first one that i have had reported. None the less i will keep an eye on it and look it over and see if there are some geometry issues that need addressed. Thank you!

@fatgum

Boosted

Can this be printed without AMS?

The designer has replied

@mrhansen7692

As in one color? No text or logo yes it could.

@fatgum

Boosted

Replying to @mrhansen7692 :

Good to know. Slicing without AMS, it shows some random artifacts on the cover/top plate first layer. Will try it out. Thanks!

(Edited)

@mrhansen7692

Replying to @fatgum :

if i have time soon ill try and upload a single color setup.

@n1mie

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

Very happy with this design. I'm waiting on M3 hardware to finish it. I was a little confused about where to put the hex keys at first, but I believe under the trays is the right place. Perhaps a spot on top would be nice, but that's mostly a preference thing. I also put the spare screws that came with my printer under the bins until I need them. I printed the outside of the case in silver with blue logo/lettering. The inside tray and clips I also printed in blue.

(Edited)

@user_639688396

Print Profile

0.2mm layer, 3 walls, 15% infill

sehr schönes Modell mit nur noch in der Anleitungen schauen welche Schrauben vorne rein passen 👍

@Woll_Vieh

Print Profile

0.2mm layer, 3 walls, 15% infill

(Edited)

The designer has replied

@mrhansen7692

Cool! Hope it works perfect>

@3DERRE

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

Gran diseño, encaja perfectamente

The designer has replied

@mrhansen7692

Very Very nice color choice! Hope you like it as much as i do mine.

@12bong13

Mega 🤓👍

@user_4200989817

Print Profile

0.2mm layer, 3 walls, 15% infill

holds everything I need. printed in place and works well! incredibly useful!

(Edited)

@3domli

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

Good modell thx ;)!

@user_91218326

Print Profile

0.2mm layer, 3 walls, 15% infill

came out great! just waiting for the hardware to complete.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(1)

Description

Comment & Rating (94)

License

Related Models

All in one test

Philips One Blade Wall Mount Stick On

NAMI (One Piece)

Two Way One Way Sign