Safe V2.0 | Vault | Bank | Money Bank | Piggy Bank by Matthew Ghost

Matthew Ghost

Household>Decor

GIF

Print Profile(5)

All

P1P

P1S

X1 Carbon

X1E

A1 mini

Safe V2.0 (0.2mm layer, 2 walls, 15% infill)

Designer

10.7 h

4 plates

4.9(337)

MiniFriendly (0.2mm layer, 2 walls, 15% infill)

Designer

12.2 h

5 plates

4.8(64)

Update From Previous Safe (0.2mm layer, 2 walls, 15% infill)

Designer

2.2 h

1 plate

4.7(13)

Multiplate and colored rings

13.3 h

5 plates

4.9(24)

Click to see more

Open in Bambu Studio

Boost

2452

4669

589

814

5.1 k

2.5 k

Released

Description

👉 NEW Safe V3 Mini 👈

🥳 Safe V2.0 is finally out! Several improvements have been added based on your requests for the previous version!🥳

The biggest change is the addition of a lock 🔐! Your safe can finally be safe! You can choose several number combinations according to your preferences 🔐
The safe V2.0 version is compatible with the previous version. Parts that remained the same (Use Update print Profile 🔥):
- 02_Spur_Gear
- 04_Rack_Gear
- 05_Frame
- 08_Hinge
- 09_Case
- 10_Screw
- 11_Pin
No Additional Parts Required😎. No complicated setup! This safe doesn't need any bearings, screws, glue or additional purchased parts.
Dimensions 140x130x140 mm. Spacious enough for your valuables, yet compact enough to fit anywhere.
Include coin slot.

Spacer problem

In some cases it happened that the spacer was too loose. More clearance is added here, for smooth turning of the dial. However, each printer has different clearances, so I recommend increasing the width of the spacer in the slicer. Until then, so that the spacer is not too loose and at the same time the dial can be turned smoothly. (The recommended step of increasing is +0.1 mm)

Assembly instruction step by step:

Number	Name	Amount
01	Door Base	1
02	Spur Gear	4
03	Wheel	1
04	Rack Gear	3
05	Frame	1
06	Retainer	1
07	Cover	1
08	Hinge	2
09	Case	1
10	Screw	4
11	Pin	2
12	Dial (#1-#6)	3
13	Spacer	1
14	Rack Gear-Lock	1
15	Spur Gear - Center	1

Comment & Rating (589)

@Tensayuken

Boosted

Print Profile

Safe V2.0 (0.2mm layer, 2 walls, 15% infill)

Almost perfect print, but don't know why the print did the cut in the upper part of the safe. I did another one and it didn't. I'm new to 3D, so maybe it's a question of seam placement? Very great job anyway :)

@user_1645236517

Boosted

That's to put coins in. 😊

@Tensayuken

Boosted

Replying to @user_1645236517 :

@user_1645236517 I mean the line behind the hole where to put coins.

@user_1645236517

Boosted

Replying to @Tensayuken :

Oh yeah that's just a seam.

@TomNL

Boosted

Print Profile

Update From Previous Safe (0.2mm layer, 2 walls, 15% infill)

Fun to print and assemble. II used super glue for more strength. Before printing, I used seam painting to to avoid having the seam on top. And, I trimmed the outer edges of the Rack Gear for a more smooth lock movement.

(Edited)

@user_1971655185

uwi

@tacit

Boosted

Awesome design! Really well done, my son loves it! One comment I'd have is the inner layer of the door was a little thin, which resulted in the locker pieces being blocked slightly by the lip. This could be remedied by a little more thickness in the inner door plate.

(Edited)

@Fluteknife

same here. I added a very small blob of pla in top and bottom of the corner and that fixed that issue.

@user_1993264460

Boosted

Same here. Easily fixed my adding some pla (superglued). Would be nice to update the print to solve this.

@GavinK42

Boosted

Great job on this! The only thing I changed was to make (and upload) a new print profile for the combo wheels, because when I printed it in 2 colors on my P1S, the numbers weren't fully formed. Assembled together easily and works great! Edit... I also manually placed the seam on the bottom of the safe.

(Edited)

@JTG_THE_MLO

what's the little box on the print for? is that takes it 2hrs?

@bman642

Boosted

Print Profile

Multiplate and colored rings

Top

The designer has replied

@miroslav.cz

Boosted

nice

@lvckyme

Boosted

I love it! works great and very creative.

@ant4hunt

Boosted

Fine design. The only problem of the actual design is the spacer for the slice dial which have the tendency to turn and block the mechanism. I think, the anti-turn profile of the slice dial is to small comparative with the axial tolerance of the slice dial cage. Anyway, I solved the problem with a little bit glue. Thank you for sharing.

@Fluteknife

I did the same. works better now

@user_1993264460

Boosted

My spacer also didn't stay in place. I superglued it to the side.

@Gavin_

Boosted

Print Profile

Safe V2.0 (0.2mm layer, 2 walls, 15% infill)

Well designed! Printed one for myself and my brother, both turned our great. Printed on the textured plate in PLA! The assembly prosses was simple and easy, and works great.

@mKotek

Print Profile

Safe V2.0 (0.2mm layer, 2 walls, 15% infill)

Printed in PLA on a textured bed. The case had a bit of warping, but luckily no functionality was harmed and it still looks ok. There were some adhesion issues with digits, hinges and cogs, so I had to force outer brim on them. Came out perfect. I love the idea, if just for fun, thank you for the fine model.

The designer has replied

@MatthewGhost

Thanks for the great review 😍

@carison1988

Boosted

A lovely and practical design

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.