P1S 90 Degree Exhaust For 100mm Ducting by Jono

Jono

3D Printer>3D Printer Accessories

IP Report

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

9 h

1 plate

4.7(7)

Modified for AMS Hub

Designer

8.8 h

1 plate

4.7(3)

Open in Bambu Studio

Boost

156

126

Released

Description

90 Degree Exhaust Vent which attaches to the P1S exhaust outlet using 4x 10x2 magnets.

Provides a 100mm opening for ducting (4 inch).

Self-Adhesive fabric lining can be used to prevent scratching, as seen in photo.

Please use the AMS modified print profile if you have the AMS hub installed.

Comment & Rating (15)

@ClevelandReefer

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

supports came off beautifully in big pieces however finish is a little rough but perfect for what I needed it for!

@TomaT3

Boosted

Print Profile

Modified for AMS Hub

Printed out without problems with PETG HF. The only problem I have, is that the 4 magnets are not strong enough to hold the exhaust. Maybe with more magnets it would be better.

@Mertyboy

Boosted

printed really well, I'm using for a spay booth build and this is perfect.

@Tbenker

Is it possible to mount it the other way round as it is? My window is on the left side of P1S. The duct is hard PU with copper rings, not easy to bend). I do not want to block poop chute or interfere with AMS and PTFE tubes. If not I have to design several parts to avoid that happening.

The designer has replied

@jonnyboi776

Hi, Yep it's possible to mount it the opposite direction, but bare in mind you'll block the poop shoot exit. Cheers

@Tbenker

Replying to @jonnyboi776 :

"but bare in mind you'll block the poop shoot exit." This was what i was concerned about. Thanks for the reply. I need to find a custom solution myself.

@corship

Print Profile

0.2mm layer, 2 walls, 15% infill

I can't get it to fit properly with an AMS HUB installed, any tips?

(Edited)

@jonnyboi776

Sadly I didn't design it with the AMS HUB in mind, but cutting a notch out of the top right corner with a sharp blade would work. I may create a version for the AMS hub later

@louspirito

Print Profile

0.2mm layer, 2 walls, 15% infill

Perfection. I actually needed this for a 2.5" (63.5mm) duct from an XTool F1 laser. A simple reduction in Bambu Studio was the solution and it printed fantastic. Thank you!

@Mertyboy

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

printed really well

@Gallivant3d

Print Profile

Modified for AMS Hub

@ColdCobra87

Print Profile

Modified for AMS Hub

@hovborg

Print Profile

0.2mm layer, 2 walls, 15% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

X1C Chamber Exhaust System HEPA/Carbon Filter Fan

Print Profile(2)

Description

Comment & Rating (15)

License

Related Models

X1C Chamber Exhaust System HEPA/Carbon Filter Fan

4" Exhaust T Joint with Clamp Seats

4" Exhaust Vent Flange with Optional Gasket

150mm to 125mm duct 90 degree elbow