CrossHatch Pattern Reusable Spool - Bambu Refill

Remixed by

CrossHatch Pattern Reusable Spool - Bambu Refill

Remixed by
Boost
57
129
33

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

Designers Profile (keep settings as is)
Designers Profile (keep settings as is)
Designer
4.2 h
3 plates
4.9(25)

ABS/ASA - 0.28mm layer, 3 walls, 15% cross hatch infill
ABS/ASA - 0.28mm layer, 3 walls, 15% cross hatch infill
4.5 h
3 plates

Open in Bambu Studio
Boost
57
129
33
22
168
125
Released

Description

Display Bambu Lab's latest infill style CrossHatch on your reusable spool!

 

My GYROID reusable filament spool was so popular, that I just had to do CrossHatch too!

 

This remix is based off the official Bambu Lab reusable spool model, so it functions exactly like the official spool, except has the added benefit of very cool infill patterns holding it all together! It also uses significantly less filament.

 

*******************************

IMPORTANT - MUST READ

You need to be using the latest version of Bambu Studio as this version has the CrossHatch available. As of the date of publish (May 16th) this will not work in OrcaSlicer or other slicers until they incorporate CrossHatch infill.

*******************************

 

 

Can I change any settings?

I would strongly advise you to NOT change any settings or modifiers in the print profile. I've spent a lot of time getting the right balance of strength and coolness, so each setting is there for a reason. The only settings you can change are filament settings if you want to print in something other than PLA.

 

 

What's the best filament to print this in?

PLA, PLA+, PLA Tough etc. are my favs here. To preserve the strength, it must print well and these print the best without missing a beat. If you dry a lot of filament, print them in PETG or ABS to avoid warping in filament dryers.

 

 

When I attach the spools, I can hear clicking. Should I be worried?

No, this is normal! The RFID tag may gently scrape against the infill patterns when closing the spool. Just keep going until it clicks in place.

 

 

Will this block my RFID readability?

Nope! Your AMS will read the tags fine with this reusable spool.

 

 

Do I need to use the spacing shim?

It's been added as a 3rd plate because the official Bambu Lab version uses it. I have never need it personally so I don't bother, but you can use it if you like.

 

Comment & Rating (33)

Please fill in your opinion
(0/5000)

Print Profile
Designers Profile (keep settings as is)
great
1
Reply
Print Profile
Designers Profile (keep settings as is)
Well done... again!!!
0
Reply
Boosted
Print Profile
Designers Profile (keep settings as is)
good design
0
Reply
Print Profile
Designers Profile (keep settings as is)
Printed out very nice using PETG filament. Snaps to together prfrctly. The crosshatch has a nice pattern.
0
Reply
Print Profile
Designers Profile (keep settings as is)
printed with ABS+, feel strong enough and saved half filament compared with the Bambu official one, thank you
0
Reply
Boosted
Print Profile
Designers Profile (keep settings as is)
(Edited)
1
Reply
Print Profile
Designers Profile (keep settings as is)
0
Reply
Print Profile
Designers Profile (keep settings as is)
0
Reply
Print Profile
Designers Profile (keep settings as is)
(Edited)
0
Reply
Print Profile
Designers Profile (keep settings as is)
Printed just fine, but unfortunately, at the expense of rigidity, which was needed. Not to worry, they will still find a home. Thank you.
The designer has replied
0
Reply
Thanks for the feedback! I might release a v2 which is a bit stiffer with a higher density of infill. Just need to balance rigidity with being able to actually see the pattern (and save filament vs the Bambu original).
0
Reply