iPhone and Apple Watch MagSafe Charging Stand v2 by totallynectar

totallynectar

Hobby & DIY>Electronics

IP Report

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

0.16mm layer, 2 walls, 50% infill

Designer

4.8 h

1 plate

4.7(53)

Less Filament: 0.2mm layer, 2 walls, 10% infill

3.4 h

1 plate

5.0(2)

Open in Bambu Studio

Boost

216

478

872

485

Released

Description

This is my version 2 of a wireless charging stand that I've designed it with a focus on sleek, simple design that feels good to use. It was designed around iPhone Pro models, but work for my other non Apple products as well (such as Google Pixel 7)

Holds and charges phones vertically or horizontally (horizontally only if they are Apple products)
Holds and charges phones with or without Magsafe cases
Holds and charges Apple Watch with original Magsafe charger
Cable organizer is designed in to the base and can accommodate both charging cables
Can be placed charger faced upwards in order to charge devices that are not magnetic or do not fit in the stand (first gen Airpod Pros, etc)
Magsafe chargers not included :)

v2 Updates:

Extended the phone front base to the bottom plane so no supports are required and it prints cleaner
Increased diameter of phone Magsafe slot so its a bit easier to insert and remove
Extended the base further backwards in order to support the watch better when it is charging without a phone
Lengthened the cable holder and improve the cable slide in joint

The imaged model was printed with Bambu Marble PLA

Comment & Rating (73)

@1800jetmech

Print Profile

0.16mm layer, 2 walls, 50% infill

Would have given it 5 stars but the supports are a nightmare to get off. I just gave up on some and left them on. Also, with the lip on the bottom, my wife’s Pro Max will not charge in the vertical position because the charging ring doesn’t line up.

@totallynectar

oh interesting, I didnt have that problem. Maybe try tree supports? I dig the color

@nu11negativ

Boosted

Print Profile

0.16mm layer, 2 walls, 50% infill

My wife was delighted, flawless print, thank you

Show original

@nu11negativ

Boosted

It was a worthwhile boost, thank you! Excellent print without errors, and the original charging cables fit perfectly Printed with Bambu P1S

The designer has replied

Show original

@totallynectar

thanks!

@Pakajoda

toller Druck

@jojos3D

Boosted

Print Profile

0.16mm layer, 2 walls, 50% infill

clean

@Pakajoda

Print Profile

0.16mm layer, 2 walls, 50% infill

All is well, the quality isn't quite to my liking, but otherwise superb

Show original

@Cnote

Boosted

Print Profile

0.16mm layer, 2 walls, 50% infill

Nice Print Thanks

@elladine

Print Profile

0.16mm layer, 2 walls, 50% infill

@user_3420233836

What iPhone magsafe charger is it based on? From a dimensional perspective

@user_1842117004

It fits the original from Apple (ca. 55mm diameter 5mm depth)

@gabbert.ct

it fits a random one I bought on amazon too. Much cheaper than the apple one

@user_600503296

Can anyone confirm that it does fit a magsafe 2 before I hit print? thanks in advance.

@felixsin

Boosted

Excellent design, I would only improve the robustness of the cable holder (for example, it broke when the supports were removed) and increase the height of the lower iPhone support by 1 mm (at least for my iPhone 14 Pro + case) Thank you

The designer has replied

Show original