DJI Avata 2 Gimbal Bumper Ver.2 by Mütze

Mütze

Hobby & DIY>RC

Print Profile(1)

All

P1P

P1S

X1 Carbon

X1E

0.2mm layer, 6 walls, 25% infill

Designer

1.4 h

1 plate

4.8(35)

Open in Bambu Studio

Boost

103

134

617

292

Released

Description

Content has been automatically translated.

Show original

I have revised the model of the DJI Avata 2 gimbal protection once more:

- Clamping force at the top and bottom has been strengthened

- I have tried to keep the field of vision as clear as possible

(only with the camera tilted downwards to the maximum is something still visible, less was not possible due to stability)

- An additional hood has been added that clips onto the mounted protection from the front. The hood can be clipped onto the installed camera protection, so that it does not have to be placed against the original DJI for storage. If the cover is too loose at the top/bottom, you can carefully heat the curves and press them together slightly on the opposite side, closing the C-shape a little bit.

Removing the cover can be a bit tricky the first few times. It is best to push/press it to one side, so that the other should come loose and it can be swung out to the front.

Camera view max. downwards - Original condition at the top - With printed protection at the bottom

Boost Me (for free)

A boost is always welcome

Comment & Rating (48)

@e.dup25

Thank you for this V2, no more problems where we saw the edge in the camera, and it holds up much better. Very good job 🙏

@Zerschmetterlin

Print Profile

0.2mm layer, 6 walls, 25% infill

Easy print. Had to figure out how to mount it. But with a bit more pressure while mounting it fits perfectly. The cam protection cover is also a nice addon. And still fits in the original bag! Nice. Thanks.

@Krateian

Hi thank you for the design Idk if others tried but when you make gimbal calibration, it hits the upper side of bumper stuck at calibration %60 so make sure to do not over look upside or do not make gimbal calibration. If mütze share the step file maybe I can try to thin middle section of the upper hook or make a hole Idk.

(Edited)

@BCO85

Print Profile

0.2mm layer, 6 walls, 25% infill

Danke für's Teilen 👍🏻

@S.janatzek1988

Print Profile

0.2mm layer, 6 walls, 25% infill

Profil gut, lediglich abbekommen nach Installation hab ich es nicht mehr >.<

@kozomeuszz

In my case, the gimbal was hitting the lower beam, so I had to file off the excess and it's ok

@Bifero

Print Profile

0.2mm layer, 6 walls, 25% infill

@user_1121395002

Boosted

Print Profile

0.2mm layer, 6 walls, 25% infill

@Semih

Hi. After Plug it, I could not remove the cover anymore. Really I am stuck with it. Even if I push/press one site, it does not work. Do you have any idea about other way in order to remove cover ?

The designer has replied

@muetzmaster

It's best to try to loosen the lower part first, then pull it up slightly and push it forward from the rear part of the drone

@muetzmaster

To remove the cover from the installed protection, you can alternatively press forward through the opening against the hook

@Semih

Thank you

@user_3081416649

Please, could someone make a Neo version?

Show original

@BG4HUN

Strong support

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(1)

Description

Comment & Rating (48)

License

Related Models

DJI Avata 2 Bumpers

Caddx GM3 / C20-T Gimbal Mount with DJI O3 Unit

AVATA 2 gimbal guard

3 Axis Gimbal with Model Rocket