Automatic Seed Starter -Self Watering Seed Starter


Print Profile(5)

0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
X1 Carbon, P1S, P1P, X1, X1E, A13.2 h
4.8
A1 mini, 0.2mm layer, 3 walls, 15% infill
A1 mini, 0.2mm layer, 3 walls, 15% infill
A1 mini, P1S, P1P, X1, X1 Carbon, X1E, A13.8 h
5.0
[Fast and Clean] 0.28mm layer, 3 walls, 15% gyroid infill
[Fast and Clean] 0.28mm layer, 3 walls, 15% gyroid infill
X1 Carbon, P1S, P1P, X1, X1E, A12.7 h
Transperent LID V6 - 0.2mm layer, 2 walls, 0% infill
Transperent LID V6 - 0.2mm layer, 2 walls, 0% infill
P1S, P1P, X1, X1 Carbon, X1E, A16.9 h
Click to see more

413
623
26
700
248
Released
Copyright Claim
Model
Comment & Rating
Remixes
Related Models

Description

Springtime, finally. Plenty of seeds that need some kind of special attention (some extra warmth, extra humidity...). Following up on my earlier simple seed starter (of which we use dozens in our small green house), here is s fully automatic (well kind of...), self-watering seed starter, mainly intended for in house (window sill, green house...) use.

It uses the same 2x2 simple seed starter from my earlier post but with an added tray, lid, and floater. Once the seedlings have started growing (and don't need special attention), you can simply remove them from the tray and put them in a green house. We are using these mostly for peppers and other seeds that need more warmth and/or humidity than they would otherwise geed in our green house (i.e. we simply put them on our heater).

PRINTING. This should be a pretty simple print. Ideally set line width to 0.5 mm (walls are 1 and 1.5 mm). Preferably use low vertical resolution for faster print. Print the lid in your favorite transparent filament and print upside down. Infill does not matter. No supports needed. I use some cheap epoxy resin for sealing my prints (i.e. making them waterproof, in this case I used it for the trays only).

FILAMENT. Use PLA for biocompatible kits or PETG if you want them to withstand higher temperatures. I use some cheap and easy to print CF PLA for the seed starters and trays, transparent for the lids.

Happy printing!


License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Comment & Rating (26)

Please fill in your opinion
0/5000

Print Profile
0.2mm layer, 3 walls, 15% infill
The model is ok, but the inserts could be adjusted so that everything doesn't wobble so much.
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
A1 mini, 0.2mm layer, 3 walls, 15% infill
works like a charm! easy to print and nice design
0
Reply
Print Profile
A1 mini, 0.2mm layer, 3 walls, 15% infill
Works great!
0
Reply
This is awesome, I can't wait to try it out.
0
Reply
Would be nice if you upload a vase mode version of the lid :-D
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
printed fantastic
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
nkce
0
Reply
this was awsommmmmmmmmmm!
0
Reply
A little kit designed perfectly with a compact design. Very lovely!
0
Reply

Remixes (0)

There are no remixes yet