TILT PHONE STAND - INDUSTRIAL by Matthew Ghost

Matthew Ghost

Tools>Organizers

Print Profile(6)

All

P1P

P1S

X1 Carbon

X1E

A1 mini

Divided into two plates - Different color

Designer

3.3 h

2 plates

4.7(44)

MiniFriendly

Designer

3.5 h

1 plate

4.5(33)

0.2mm layer, 2 walls, 15% infill

Designer

3.1 h

1 plate

4.1(35)

A VERSION WITH CLEARANCE

Designer

3.1 h

1 plate

4.5(12)

Click to see more

Open in Bambu Studio

Boost

405

755

149

1.7 k

1.1 k

Released

Description

The stand allowing you to comfortably and securely hold your mobile phone at the optimal viewing angle.

Thanks to the worm gear, it can never happen that the stand with your mobile falls flat.
Thanks to the combination of a worm gear with bevel gears, the stand enables easy and smooth tilting.
Compatible with charger.
It is not necessary to glue the parts here. (Otherwise I made a profile where there are parts with clearance. This version requires the use of glue)
Smooth design
Different colors can be used for mechanical parts (Profile: Divided into two plates - Different color).

Assembly instruction:

Instructions can be found in the video below. Please follow the procedure: (video)

https://www.youtube.com/shorts/9PywQ-fwkmk

Groove clearance problem:

If there is too big clearance in the guide groove (02_Gear and 03_Base), it may happen that the 02_Gear tilts too much and the 01_Worm gear will not engage (the stand will not tilt). If this situation occurs, I recommend slightly pushing the left side of the 02_Gear and turning with the 06_Adjustable_Gear.

A VERSION WITH CLEARANCE

It may happen that main version will not be assembled due to small clearances. Actual clearance depends on many factors (flow, filament, printer condition)
Parts with the letter C in their name are parts that have increased clearance. These parts must be glued

adjustable phone stand

Comment & Rating (149)

@Fur_Okamio

Print Profile

MiniFriendly

Printed well, just a few surface defects but these are more likely due to the old/wet PLA I used. The worm gear and the "phne gear" tend to jam while moving for me. Seems like the angle from the teeth the worm gear - phone gear aren`t just right. All in all still a very good looking model!

(Edited)

@BiscottoSupremo

Print Profile

A VERSION WITH CLEARANCE

Print only the base with C and used with the "standard" version. All good! Thank you!

@BiscottoSupremo

After some use I noticed that the front "pitch" can be slightly shorter to allow you to tap the virtual button on Android devices or the Touch ID button on older iPhones. I'm using these mounts with some development's devices, so I have to switch apps frequently.

@warrell72

Print Profile

0.2mm layer, 2 walls, 15% infill

print quality was great, model could use a wider base for more stability

@codemania

Agree, such as the star-like round base, so it can support a 12-inch iPad Pro.

@SigmaT4

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed with Bambu lab matte PLA. Great engineering, well done. I don't know why my model is so grippy though. I think that the fact that the worm gear is on one side only and that it has a lot of clearance with the gears tilts the rotating part sideway and jam. I would love to see a model with dual worm gear. Also my print warped but that is on me. (it warped on an aesthetical parts so it does not interfere with the mechanism)

@codemania

Maybe PLA is not suitable for such complex gears? Try switching to PETG ？

@FamousThomas

Boosted

Print Profile

Divided into two plates - Different color

Very nice design. Many Thanks I kept all settings the same bur changed to tree support which results in a more clean surface on the cable entrie area.

@VTKeGGeR

Boosted

Print Profile

Divided into two plates - Different color

No issues at all!

@samur.isma

Print Profile

Divided into two plates - Different color

great mechanics but very unstable. Honestly I regret printing it.

@jefflad

Nice phone holder

@user_1876678171

Boosted

Print Profile

Divided into two plates - Different color

This version of the phone stand I like most. I appreciate that everything can be printed. No buying of screws, bearings, etc. Thank you for the model

@user_1492791003

Boosted

Print Profile

Divided into two plates - Different color

АБС печатал

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Print Profile(6)

Description

Comment & Rating (149)

License

Related Models

Tilted Bin for Multiboard - 1x1

Tool Drill bits holder with tilt Gridfinity

Tilting Shoe Organizer

Modern Headphone Stand