YOYI YOYI Bambu Lab AMS Cardboard Spool Adapter Ring

YOYI YOYI Bambu Lab AMS Cardboard Spool Adapter Ring

Boost
5
5
5

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
Designer
34 min
1 plate
5.0(3)

Left-hand side adapter - 0.2mm layer, 2 walls, 15% infill
Left-hand side adapter - 0.2mm layer, 2 walls, 15% infill
Designer
26 min
1 plate
5.0(2)

Open in Bambu Studio
Boost
5
5
5
1
13
12
Released

Description

This model widens one side of the spool ring adapter to stabilize a YOYI YOYI 1kg 195x61mm cardboard spool while it rotates within a Bambu Lab AMS.

 

Features:

  • Reusable
  • YOYI nameplate for easy identification when reusing

Instructions:

  • Measure your spool first to ensure it matches the specified dimensions.
  • Print one of each model for a single spool.
  • Affix the wide spool ring adapter on the right-hand side of the YOYI YOYI spool if you're facing the AMS.
  • See attached photos.

Considerations:

  • Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.
  • Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.
  • AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an AMS Lid Riser which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on my profile or directly here: https://makerworld.com/en/models/33133

Comment & Rating (5)

Please fill in your opinion
(0/5000)

Print Profile
Left-hand side adapter - 0.2mm layer, 2 walls, 15% infill
1
Reply
Print Profile
Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
1
Reply
Print Profile
Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
Left-hand side adapter - 0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
0
Reply
No more

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.