Download from the domestic region and search for turbofan

Pathfinder.Ant

It still doesn't work, could you please send it?

user_3999124684

Turbofan （main body） 来自 Pathfinder Ant - MakerWorld

大佬这个下载不了，能辛苦私发一下吗

Hey, I can't download this. Could you please send it privately?

不知道是不是我印的問題，腳架角度並不可調，而且風扇本體跟腳架的安裝有點反人類，沈頭螺絲的孔徑建議再放大
3mf的檔案貌似有一些檔案是用不上的可以再更新一下

I'm not sure if it's a problem with my printing, but the tripod angle is not adjustable, and the installation of the fan body and the tripod is a bit counterintuitive. The diameter of the countersunk screw holes should be increased.
The 3mf file seems to have some unused files that can be updated.

s5862140

0.2mm layer, 5 walls, 15% infill

感谢你的评论，首先你这颜色漂亮的很，第二这个角度确实调整的不是很好，我再想想办法，第三关于反人类这个问题，我也没想到好的办法，哈哈，第四关于调整孔径的建议，我后续更新下，再次感谢你的评论

Thank you for your feedback. Firstly, the colors you chose are really beautiful. Secondly, the angle you chose isn't ideal, I will think of a better solution. Thirdly, about the "anti-human" problem, I haven't found a good solution yet, haha. Fourthly, about the suggestion of adjusting the aperture, I will update it later. Thank you again for your feedback.

懒癌终结者LAZJZ

去国内区搜索turbofan吧，我也不知道什么情况

Search for turbofan in the domestic area, I don't know what's going on either

都是同一个问题看不到文件啊！哭了

It's the same problem, I can't see the file! 😭

user_1286956187

这两个垫片的具体位置在哪？谢谢

Where exactly are these two spacers located? Thank you

瑞瑞

There are files, how can there be no files?

I always see this interface when I open it

chunfeng

我这打开没问题，实在不行你去国内去下，国内去搜索Turbofan

I can open it without any issues. If you really can't open it, try searching for Turbofan in China.

我这两天出个视频放在评论区，注意这两天你看看


I'll be posting a video in the comments section in the next couple of days, keep an eye out!

GiantRobotsYES

cover

8caed4855e1aec9b23af5754cb30fa3_307a94fc-d3bc-45c8-b836-b5eb49c5bc54.jpg

屏幕截图 2024-07-28 161741.png

屏幕截图 2024-07-28 161758.png

2024-07-28_9109777c9ab5e

_(1).2024-07-28_760a4314532c3

_(2).2024-07-28_c7b77e4168736

_(3).2024-07-28_132dcb45215df

_(4).2024-07-28_dee3a214f2fab

plate_1.png

plate_2.png

10填充，可狂暴打印，具体自行测试

plate_3.png

plate_4.png

墙顺序：外墙内墙

plate_5.png

小煜

4层墙，部分需要支撑参数已经调整好，经过我个人测试非常容易拆除，有条件用petg做支撑面效果更好主要第五盘说明内外墙顺序，因是内螺纹经过测试用外墙内墙会有悬垂坠落，因此改为外墙内墙

4 walls, some support parameters have been adjusted, after my personal test, it is very easy to remove, if you have the conditions, use petg to make the support surface, the effect will be betterMainly the fifth plate explains the order of the inner and outer walls, because it is an inner thread, after testing, using the outer wall and inner wall will have a hanging fall, so it is changed to the outer wall and inner wall

0.2mm layer, 4 walls, 10% infill

飞机发动机风扇（二）底座风扇主体详见：https://makerworld.com/zh/models/189875#profileId-209496

Aircraft Engine Fan (Part 2) BaseFor the main fan body, see: https://makerworld.com/zh/models/189875#profileId-209496

Print Profile(1)

Description

Comment & Rating (17)

License

Related Models

Aircraft engines

Articulated Engine Keychain

Wankel engine - orbiting

Propeller aircraft engine