Gear heart fidget toy keychain

Gear heart fidget toy keychain

Boost
364
522
139

Print Profile(5)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
49 min
1 plate
4.6(89)

0.2mm layer, 2 walls, 8% infill
0.2mm layer, 2 walls, 8% infill
49 min
1 plate
4.8(10)

A1 mini, 2 colors, 0.2mm layer, 2 walls, 15% infill
A1 mini, 2 colors, 0.2mm layer, 2 walls, 15% infill
52 min
1 plate
4.8(9)

125% scale, 0.2mm layer, 3 walls, 10% infill
125% scale, 0.2mm layer, 3 walls, 10% infill
1.4 h
1 plate
5.0(3)
Click to see more

Boost
364
522
139
0
1.6 k
1.2 k
Released

Description

V2 WITH REINFORCED PINS AND NO CAPS HERE

 

If you want a model without the keyring hoop you can check out this remix I made.

 

Assembly instructions:

 

Print the base, gears and 2 caps and assemble. You may need to glue the caps to the base's gear axis.

 

To legally sell PRINTED models, you may obtain my permission through this link:

https://www.patreon.com/SpikeMix3D

Comment & Rating (139)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 2 walls, 15% infill
Really cool model, unfortunately one of the pins broke really easily while assembling it. Should make them a little bit thicker.
(Edited)
4
Reply
Thanks for the suggestion, I just uploaded the modified version with thicker pins. Made them 3mm diameter, they were 2mm before.
(Edited)
2
Reply
Replying to @Spike_mix :
Great that you listen to feedback, changed my rating to five since the small problem is now fixed. Love the model!
(Edited)
2
Reply
Congratulations and thank you very much.
The designer has replied
2
Reply
I made a new version where I reinforced the pins and use C clamps instead of caps: https://makerworld.com/en/models/197382
0
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
Printed well, although I would recommend making the diameter of the gear pins larger. it was dropped once and the gear broke off, twice on two separate prints. I used Bambu PLA. Could use a stronger material if you are going to handle or even play with it.
(Edited)
0
Reply
I made a new version where I reinforced the pins and use C clamps instead of caps: https://makerworld.com/en/models/197382
0
Reply
Replying to @Spike_mix :
Awesome! I'll try it out!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
awesome fidget. pin for big gear seems to break easily. so switched to 3mm bolt and nut.
0
Reply
I made a new version where I reinforced the pins and use C clamps instead of caps: https://makerworld.com/en/models/197382
0
Reply
I also had issues with the fragile pins breaking off so after the 2nd attempt I just drilled holes and added screws. the gear holes are drilled a little wider than the screws enough to spin freely and not grab the screw threads and the holes on the heart a bit smaller than the screws so they grab tight and only about half way into the plastic so it doesn't go through then cut the screws shorter with a Dremel cutoff wheel so they could be tightened snug and not break through the back. works perfectly.
(Edited)
The designer has replied
0
Reply
I made a new version where I reinforced the pins and use C clamps instead of caps: https://makerworld.com/en/models/197382
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Great and beautifu model. Perfect.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
molto bello, grazie
0
Reply
A great design. Worked perfectly. thank you for the upload
0
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
my mum loved it
0
Reply
Scale to 80% and still works perfect
0
Reply