P1S Storage System

P1S Storage System

Boost
222
352
45

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
23.8 h
4 plates
4.8(22)

0.2mm layer, 2 walls, 15% infill, Multicolour
0.2mm layer, 2 walls, 15% infill, Multicolour
24.4 h
4 plates
4.8(5)

Boost
222
352
45
0
464
358
Released

Description

This is my version of a P1S storage looks like the actual printer down to that basic screen (we all love) has 6 drawers with supportless handles.

the top under the lid is 29mm deep, 129mm wide, 140mm long, the 2 drawers inner diameter is 54.5mm, tall 137.5mm, 40.17mm wide the 2 middle drawers are 22.38mm tall, 137.5mm long, 54.5mm wide the bottom 2 drawers are 22.7mm tall, 137.5mm long, and 116.5 wide at it present scale. 2pcs. need support the handle knob for the top lid (glass plate) and the top of the main body where the top lid goes on there is a set of 4 feet you can print in PLA or TPU you can pop on the bottom. The P1P version is in the raw files. Happy printing and thanks for looking.

 

For the X1C version

https://makerworld.com/en/models/180224#profileId-198257

Comment & Rating (45)

Please fill in your opinion
(0/5000)

Hey! Love this, It's currently still printing but I just wanted to say that from the RAW files, the lid does not fit snuggly.
The designer has replied
1
Reply
I can increase it a little more was worried if someone's printer not dialed in
1
Reply
and could print it at 101% on the y axes that's where I shrunk it a little just to be safe.
1
Reply
also add a tight lid in the raw files top lid (2)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Super nice model with no problems
The designer has replied
1
Reply
Thanks looks great glad you liked it
0
Reply
they look good glad you liked the model Thanks
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
passt perfekt zusammen. Klasse Arbeit
The designer has replied
1
Reply
Das sieht toll aus. Ich freue mich, dass dir das Modell gefällt Danke
0
Reply
thank you
The designer has replied
1
Reply
Thank you glad you liked it
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
come out great worth the print love it.. thanks
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Multicolour
Perfekt *****
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printing with PETG. Was printing fine and then I noticed runs on the side below logos. Then a bunch of spaghetti, then pieces of top had fallen off. not sure what went wrong
(Edited)
Other Issues:Used generic PETG profile on Bambu studio
The designer has replied
0
Reply
looks like started to clog are got wet since went from flat color to shiny color I printed all mine in PLA sorry you hade an issue with petg it looks like a lot of ghosting at the logo too but it could be just the picture angle
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
that looks great thanks for showing
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Multicolour
What can I say it printed great I used my P1 for the main and the A1 for the drawers
The designer has replied
2
Reply
Thank you for your Rating!
(Edited)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
great design
The designer has replied
1
Reply
Thanks
0
Reply