Nordic Table Set

Copyright Claim

Nordic Table Set

Boost
110
196
29
This model is created by Make My Vase
Make Your Model

Print Profile(2)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

0,4mm Nozzle VASE MODE 1mm Wall width
0,4mm Nozzle VASE MODE 1mm Wall width
Designer
3.5 h
3 plates
4.6(10)

0.6mm nozzle VASE MODE
0.6mm nozzle VASE MODE
Designer
3.5 h
3 plates
4.5(4)

Boost
110
196
29
0
232
141
Released

Description

Decorate your space with this stylish set consisting of a bowl, a vase and a tealight candle holder.
I strongly recommend using a LED candle.

This profile is optimized for printing with a 0.6mm nozzle and an extrusion width of 0,8mm.
If you don't have a 0.6mm nozzle - reach out and maybe we can work something out other nozzle sizes.

- Or use the attached raw files to test out yourself!

Click Here to see the matching set of small planters.



Happy Printing!

Comment & Rating (29)

Please fill in your opinion
(0/5000)

Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
top😝👌🏿Thanks🙏🏿
The designer has replied
1
Reply
Looks great! :)
(Edited)
1
Reply
Replying to @Makefy :
🙏🏿🙏🏿🙈🙏🏿
0
Reply
Print Profile
0.6mm nozzle VASE MODE
Printing failed from layer 100, but maybe it's the petg-basic. I'll probably try again.
The designer has replied
0
Reply
Haven’t tried this model with PETG myself but could possible be some warping issues in combination with the constant overhang. Can’t tell exactly from your photo but slowing down might help. Really hope you can figure it out :)
0
Reply
Replying to @Makefy :
Yes I also think it was the speed, it just didn't connect the layer well enough. I will probably also reduce the cooling a little.
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
printes with Spectrum fillament
0
Reply
They turned out amazing. Did the three pieces from this set as well as the small planter/vace. Did this in kingroon pla black.
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
Strength Issue
The designer has replied
0
Reply
Hi 😊Could you provide a picture to help me understand the problem?
0
Reply
Replying to @Makefy :
Hi ^^, the design is fantastic but I think it's a printing profile problem, I tried to print (PLA) twice starting from the smallest one, the first time I detached the piece from the plate and the bottom remained attached to the plate itself. In the second case I waited for it to cool, and it only came off on one side. I think the bottom is too thin.
0
Reply
Replying to @makerlab_it :
Thank you :) Could you try to put the printer in silent mode to slow it down a bit - and then make sure to let the print cool down completely before twisting the plate to release it? If you have no luck with this I can make a version with a thicker bottom :)
0
Reply
Thank you for sharing this beautiful set you created. Can’t wait to print a few to give as gifts.
The designer has replied
1
Reply
Glad to hear you like it! Hope to see a picture of your prints soon :)
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
Very nice
The designer has replied
0
Reply
Thank you :)
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
Beautiful models! thank you!
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
The overhangs make the outer texture a little rough and undefined.
0
Reply
Print Profile
0,4mm Nozzle VASE MODE 1mm Wall width
The designer has replied
0
Reply
Thank you 😊
0
Reply