Modular Slidey Storage Pod - Wall Mounted For Tools/Parts/Medicine

Copyright Claim

Modular Slidey Storage Pod - Wall Mounted For Tools/Parts/Medicine

Boost
344
567
52
GIF
GIF
GIF

Print Profile(3)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
Designer
13.7 h
6 plates
4.9(23)

Bambu Door, 3 Colour, 0.2mm layer, 2 walls, 15% infill
Bambu Door, 3 Colour, 0.2mm layer, 2 walls, 15% infill
Designer
2.7 h
1 plate
5.0(5)

Red Cross Door, 0.2mm layer, 2 walls, 15% infill
Red Cross Door, 0.2mm layer, 2 walls, 15% infill
Designer
2.3 h
1 plate

Open in Bambu Studio
Boost
344
567
52
13
623
350
Released

Description

Modular Slidey Storage Pod

 

 

Features:

  • 3 Shelves For Storage
  • 1 Full Pod Prints In Under 9 Hours
  • Easy Assembly
  • Sliding Door
  • Stylish Design
  • Great For Use As A First Aid/Medicine Cabinet
  • Can Be Colour Coded For Different Purposes
  • Perfect For 3D Printer Parts, Adaptors, Cables, SD Cards, USB Sticks, Scrapers And Anything Else That Will Fit!
  • Easy Removal From The Wall For Simple Loading, Unloading And Organizing
  • Modular System That Can Be Mounted In Horizontal And Vertical Rows (Single And Double Mounts Included)
  • Strong And Reliable Storage Solution
  • Can Be Printed On An A1 Mini
  • 3 Different Labelled Doors Included - ‘Parts’, ‘Tools’, ‘First Aid’

 

Assembly:

  • Glue the ‘Shelves’, ‘Side Left’ and ‘Side Right’ together.
  • You only need to add glue to the very edge of the shelves and then seat them in the slots in each side piece.
  • Once the glue is dry, insert the door through the grooves that are cut in the door channel
  • Ensure the door is in the correct orientation as it slides in from back to front
  • Slide the door all the way round its channel until it meets the stop at the front
  • Insert the 2 small stop pieces to close off the door channel. This is optional as once mounted on the wall, the door handle acts as a stop.

Assembly should take no more than 5 minutes.

 

During assembly you must ensure all edges of the shelves are seated into their corresponding slots. If they are not all the way in then the sliding door will not function correctly.

 

Add some lubricant to the slots that the door slides in, for a smooth motion. I use silicone grease and it works great.

 

Tip: You can make the pod any width you like! - You just need to scale the shelves and the door up or down in Bambu studio.

  • To do this, scale both parts in the X-axis only and ensure the door is always 2.9mm narrower than the shelves.

 

This design is the first version I have made of this concept - If you have any issues or recommendations for edits or additions, please leave a comment or message me! I'm open to constructive feedback to make this as good as it can be :) - It would also be good to add some additional features that users may want to see in the future. I already have some ideas, but would love to hear what you think too!

 

Thanks for looking!

 

Please share your makes with this one! - I had a fun time designing this and am very happy with how it turned out.

 

Also, please rate and review your printing experience :) - It helps my designs get seen by more people :P

Comment & Rating (52)

Please fill in your opinion
(0/5000)

Boosted
Print Profile
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
Works great! 2nd one is printing now.
(Edited)
The designer has replied
2
Reply
Appreciate the feedback! Thank you for printing :)
(Edited)
1
Reply
Print Profile
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
I wanted to get it glued and hung/used before leaving my review. it's been a few days now and I really dig it! it works well, looks great. I'll be printing another! Nice design, thanks!
The designer has replied
1
Reply
Looks perfect! Thank you for printing and leaving a review :)
0
Reply
What are the two "Generic-Cube" parts for? They show as semi-transparent on the Slides and Stops plate in Bambu Studio
The designer has replied
1
Reply
They are support blockers :) - Just to stop it printing support in the grooves. Thanks.
2
Reply
The designer has replied
1
Reply
Thanks for printing! :) Looks great!
0
Reply
Print Profile
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
Going to use your door as a "tube container" wall. This way I can show the textured surface.
1
Reply
Print Profile
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
bella
0
Reply
worst 3-D printed, build ever none of the pieces go together I would not recommend this.
0
Reply
Print Profile
Bambu Door, 3 Colour, 0.2mm layer, 2 walls, 15% infill
A nice shelf to store small printer stuff which is everytime laying around. Perfect print and fit. No problems with the assambly. Shelf and side panels printed in Anthrazit PETG. Door printed in Bambulab PLA.
0
Reply
Print Profile
All Parts, 3 Extra Labelled Doors, 0.2mm layer, 2 walls, 15% infill
Perfekt - mega sauber
0
Reply
Print Profile
Bambu Door, 3 Colour, 0.2mm layer, 2 walls, 15% infill
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.