Rocket with Boosters (2 Sizes)

3DPmom
Toys & Games>Other Toys & Games
Copyright Claim

Rocket with Boosters (2 Sizes)

3DPmom
Boost
2373
4194
940

Print Profile(11)

All
A1
P1S
P1P
X1
X1 Carbon
X1E
A1 mini
Large Rocket, 0.2mm layer, 2 walls, 15% infill
Large Rocket, 0.2mm layer, 2 walls, 15% infill
Designer
7.6 h
3 plates
4.9(138)
Small Rocket, 0.2mm layer, 2 walls, 15% infill
Small Rocket, 0.2mm layer, 2 walls, 15% infill
Designer
21.8 h
3 plates
4.9(86)
Less Color Change Variant - 0.2mm layer, 2 walls, 15% infill
Less Color Change Variant - 0.2mm layer, 2 walls, 15% infill
1.5 h
1 plate
4.8(98)
0.2mm layer, 2 walls, 5% infill
0.2mm layer, 2 walls, 5% infill
1.2 h
1 plate
4.7(215)
Click to see more
Open in Bambu Studio
Boost
2373
4194
940
388
8.5 k
5.8 k
Released

Description

These are fun rockets with boosters that extend on take-off. I designed two sizes and each contain two parts: the main rocket body and the boosters. The larger rocket has four small boosters and the smaller rocket has one large booster.  These make great little gifts or party favors 🚀

 

Layer Height 0.2mm

PLA works great

15-20% Infill

Supports needed for the area around the boosters on the Large Rocket

 

Dimensions of Large Rocket: 4in x 2 3/8in

Dimensions of Small Rocket: 3 1/4in x 1 7/8in

 

There are two ways you can print these rockets (I included both in their print profiles):

  1. Print the complete rocket: this prints great but if you want multi-color for the boosters (and/or fins) it’s going to take some time (I found 8-10hrs)
  2. Print the boosters first, print the rocket second pausing at layer height 15.6mm for the large rocket and 30.6mm for the small rocket, drop the boosters in and then continue printing. This method is much faster:)

 

In the print profile for the small rocket I included the complete rocket to print on plate #1. On plates #2 & #3 I separated the rocket from the boosters, so they can be printed separately (make sure to print the boosters first:)

 

In the print profile for the larger rocket I included the complete rocket to print on plate #1. On plates #2 & #3 I separated the rocket from the 4 sets of small boosters so they can be printed separately (again make sure to print the boosters first:)

 

Note: supports are needed for the larger rocket at the base around the rings for the boosters. I have included those supports in my print profile. (Also note if you are printing plate #3, I did not include supports in the booster chambers so that they are clear to drop the boosters in:)

 

My designs are free for personal and non-commercial use. If you would like to sell them for commercial use, send me a message and we can discuss the details:)

 

If you like my work and want to help support it, you can buy me a Diet Coke at https://www.buymeacoffee.com/3dpmom 

Thanks so much!

 

Have fun printing these…they’re a blast 🚀

rocket
3drocket
3dpmom
fidget
space
spaceship
rocketship
ship
shuttle

Comment & Rating (940)

Please fill in your opinion
(0/5000)
level
@drshelby
Print Profile
Large Rocket, 0.2mm layer, 2 walls, 15% infill
Turned out really cute but the tolerances were too tight on the flames so they didn't extend (probably because I used a 0.6 mm hot end)
The designer has replied
0
Reply
level
@3DPmom
That is interesting. I haven't tried printing these with a 0.6mm hot end and now I am curious about it affecting the tolerances...
0
Reply
level
@drshelby
It seems like they were not sealed the entire way up, just along the z-seam. I tried to pop it apart but couldn't get a good hold of it.
0
Reply
level
@mshaf2
Replying to @drshelby :
I just confirmed this. The .6 hot end does not work with this one. stick with the .4 and it works great.
0
Reply
level
@nicholas.good03
Print Profile
Small Rocket 0.2mm layer, 2 walls, 15% infill
4
Reply
level
@3DPmom
These look awesome:) Did you print them all at the same time? How long did they take?
1
Reply
level
@nicholas.good03
Replying to @3DPmom :
I did!! I think around 11 hours and I used 65% purge volume instead of 100, too, to cut down on 💩 from all the color changes.
0
Reply
level
@SupaDupa
Replying to @nicholas.good03 :
wow. awesome. did you need supports?
1
Reply
level
@amanda.loughnan
Print Profile
Large Rocket, all printers, 0.2mm layer, 2 walls, 15% infill
really fun print. printed in Bambu PLA basic silver and red.
5
Reply
level
@bushmg1
Very nice design! I printed them both on the X1C using Prusa PLA "Lipstick Red", Bambu PLA Basic "Grey", and Bambu PLA Silk Dual-Color "Gilded Rose." Note to self: read the instructions more carefully! If everything is printed separately, the rocket flames won't go back into the rocket, LOL! Thanks for the tip to pause and insert the flames before continuing. It saved a lot of time and filament! edit: Sorry - I forgot to give a rating - 5 stars! I guess I can't go back and do it now :-(
(Edited)
4
Reply
level
@BaklavaBaby29
Print Profile
Large Rocket, all printers, 0.2mm layer, 2 walls, 15% infill
as described works well! really appreciate the support block on the centre of the booster
3
Reply
level
@3DPmom
This looks awesome 🤩 Thanks for sharing:)
1
Reply
level
@The_Siege
Print Profile
Small Rocket, 0.2mm layer, 2 walls, 15% infill
Printed Fine But doesn’t come out all the way
0
Reply
level
@user_3506402051
try gently tugging on the innermost "flame" to smooth out the edges inside. try using needle nose pliers or tweezers pinched onto the rim/outside of the tiniest part in the middle. it worked for me!
0
Reply
level
@The_Siege
ok thanks
0
Reply
level
@Gollem
Print Profile
0.12mm 5% infill Easy-to-remove base layer, anti-collapse and broken corner A1mini
Had no issues printing. came out perfect. The telescoping feature did not snag. 10/10, toddler approved
The designer has replied
1
Reply
level
@user_3840573519
It was so much fun
0
Reply
level
@will.michaux
Print Profile
Small Rocket 0.2mm layer, 2 walls, 15% infill
No problems at all on a Bambu Labs X1C with AMS. Worked great and fun to show off. For the flames I used a rainbow filament with a long transion that just happened to on that gold color. oMy only nit is that it wasn't clear from the description whether the pause was included in the profile and I waited anxiously to see if I had to hit pause at just the right time. For those wondering... ** The pause is included in the profile. ** Thank you for the model and the profile.
(Edited)
2
Reply
level
@aaronste1nke
Nice little model; great idea to print the flames separately and then pause the print. Printed with Bambu Lab PLA Matte Ivory White, Bambu Lab PLA Basic Red, and eSun PLA Silk Dual Color Green/Blue.
2
Reply
level
@KanoaN
Print Profile
Large Rocket, 0.2mm layer, 2 walls, 15% infill
cool rocket
(Edited)
2
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

NASA SPACE SHUTTLE WITH ROcket BOOSTERS

NASA SPACE SHUTTLE WITH ROcket BOOSTERS

PAL PRINTS
0
3
7
Radiator booster fan adapter

Radiator booster fan adapter

BENOengineering
1
37
20
dB BOOST 2.0 - Sound Booster and Phone Stand

dB BOOST 2.0 - Sound Booster and Phone Stand

Peter Martin
1
6
9
Rocket fidget
GIF

Rocket fidget

3D prints and gifts
1
15
53
PrivacyTermsGuidelinesFAQCookie SettingsHot Searches
© 2024 MakerWorld