Gridfinity storage for A1 nozzles by Luke

Luke

3D Printer>3D Printer Accessories

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

v2 - no lip, easier insert

Designer

2.5 h

1 plate

5.0(18)

Open in Bambu Studio

Boost

104

256

310

214

Released

Description

Gridfinity storage for A1 series nozzles. The uploaded profile was printed in ABS/ASA but any regular filament should work fine.

Looking for storage for H2D nozzles because they seem pretty similar? They are not, but luckily I have adapted this model for the H2D :) Please take a look over here!

Note that the latest print profile has a slight modification to remove a lip that was inhibiting insertion of the nozzles. You’ll see this discussed in the comments and I went ahead and made that change :)

Original Onshape CAD is available here.

a1mini

gridfinity

Comment & Rating (57)

@SaltydogNC

I found the issue with the tight fit. It isn't actually the tolerance. The back edge of the nozzle body slot has a lip that extends into the body slot opening. You can feel this with your thumb. If this lip is removed, the nozzles fit easily. The lip is causing the nozzle to enter at an angle and bind.

(Edited)

The designer has replied

@hagmonk

I could make that adjustment and upload a revised model if you think that's worth it!

@SaltydogNC

Replying to @hagmonk :

That would be great. I used a knife to trim that area away and it made inserting the nozzles effortless. Thanks so much!

@hagmonk

Replying to @SaltydogNC :

No worries, let me figure out how to get that fixed up and I'll do a test print, then get it uploaded

@GSGSG

Boosted

Print Profile

v2 - no lip, easier insert

I was unsure about if I was going to like this print. Then I printed and I love it - great job. Well done 10 STARS.

@hagmonk

Fantastic, looks amazing!

@Nyni

Print Profile

v2 - no lip, easier insert

Absolutely stunning! Few containers boast six seats. Printed with PLA Matte Earth, 0.4 nozzle, 0.20 layer.

Show original

@exabyde

Boosted

Print Profile

0.16mm layer, 2 walls, 10% infill

I think this is the best one for nozzle storage, since the area takes only 2x2 units for 6 nozzles. I didn't utilize 2 colours, since this sits in a drawer anyway :D

@spatarescuandre

Print Profile

0.16mm layer, 2 walls, 10% infill

A bit tight but iy s nice

@Dexter1214

Print Profile

v2 - no lip, easier insert

Perfect print

@karolans

Print Profile

v2 - no lip, easier insert

Perfect, thank you

@BlindBadger

When I check the model in the slicer, the V2 model doesn't have the gridfinity part on the bottom. Was that missed when updating it?

The designer has replied

@hagmonk

Oh really?? I'm not sure how I could have missed that. I'll correct it straight away

@hagmonk

Replying to @hagmonk :

Thank you for bringing that to my attention; I've uploaded a corrected model just now!

@user_354781549

The top part is extremely nice and fits the nozzles just perfect. However for me the bottom part was ever so slightly to small or rather the gaps to "click" onto the base plate had just a bit to little space to fit the baseplate properly. This is the only gridfinity accessiory so far that has this issue. First I thought it might be due to scaling or something. And if i wanted to I could push it down and it "clips" onto the baseplate, but my idea is having magnets to pull the tray down by itself. Nobody else had this issue?

The designer has replied