Wicked winged heart

Copyright Claim

Wicked winged heart

Boost
82
111
19

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
3.5 h
3 plates
4.2(12)

Boost
82
111
19
0
129
159
Released

Description

For the best results of printing this design please check out the remix by plasonite

https://makerworld.com/en/u/3776083722

 

Happy valentines you wicked ones!! Haha

Love the colors, Duramic silk red and CC3D Black Marble PLA, just pop together.

To create this wicked heart make sure to use a brim when printing the main heart piece and it should print out just fine without supports, in fact non of the parts will need supports.

I included two different tails a shorter one as in the picture and a tall one. Witchever you prefer, again no supports needed.

I would recomend glueing the heart to the tail first and letting it set up for awile before attempting to glue the other pieces on to the heart.

The horns should just press into place without issue.

The wings I printed out flat to the build plate, and once everything was glued together I hit them lightly with a heat gun / hairdryer to give them a stylized look

I printed out the wicked smile and hit it with a heat gun as well, shapeing it around the heart before glueing it into place.

The tail point top and bottom I glued together before attaching it to the tail itself.

I highly recomend 3D gloop as glue for this model as the conection between the tail and heart broke free on me when useing just Super Glue / C A glue. If you dont have any 3D gloop, try fileing or sanding the tail part flat before glueing the heart on top.

You can follow me on instagram, https://www.instagram.com/pla.n.pa/

to find out what I designs I am currently working on

If your interested in selling prints of my designs, become a Patreon supporter here…
https://patreon.com/planpa3d

Thanks for checking out my design.

Have fun and happy printing!!

Print Settings

Rafts:

No

Supports:

No

Resolution:

.2

 

Category: Art

Comment & Rating (19)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 2 walls, 15% infill
print hit and fell off plate. Mouth says smaller than actually turns out
0
Reply
Check out my remix here: https://makerworld.com/en/models/132166#profileId-143294 I fixed the scaling on the mouth and made it easier to assembly.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
davvero particolare e fatto bene
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The wicked smile is scaled improperly, the rest printed great
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
mouth too big. Parts not efficiently distributed on build plates.
0
Reply
I did a remix on the mouth (sized it and made an easy cutout for a smoother assembly) https://makerworld.com/en/models/132166#profileId-143294
0
Reply
What is wrong with this? 2 bases 2 tail ends mouth way too big. What am I missing?
0
Reply
I did a remix that resolved a lot of this: https://makerworld.com/en/models/132166#profileId-143294
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Everything is in standard size except for the black smile, which is 200% or some large number. That needs to be fixed on this print profile.
0
Reply
Check out my remix for a smoother mouth setup. https://makerworld.com/en/models/132166#profileId-143294
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
awsome came out very nice love it
0
Reply
The Heart has failed 3 times at the exact same layer height..the hotend knocks it over. I really like the design and I dont want to give you a bad review..also the parts , especially the mouth is not to scale.
0
Reply