Phone Stand (No AMS needed) by Reckit

Reckit

Tools>Gadgets

Print Profile(10)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

Merged Accent Version for AMS

Designer

1.7 h

1 plate

4.9(587)

0.2mm layer, 2 walls, 8% infill

Designer

1.4 h

2 plates

4.9(1.2 k)

Brim,0.2mm layer, 2 walls, 7% infill

1.6 h

2 plates

4.9(207)

A1 mini compatible, with AMS 0.2mm layer, 2 walls, 8% infill

1.6 h

1 plate

5.0(21)

Click to see more

Open in Bambu Studio

Boost

3032

5188

2529

1.4 k

18.7 k

17.5 k

Released

Description

01/03/2024 Added a merged accent version for AMS printing

Added an accent profile with two more options for people who are having issues with fitting them to holder.

The stand is designed to hold the phone with or without a case. Accents on the side are printed separately and fitted in after being printed

No AMS is needed for dual-color print.

Accents are a tight fit so position them into place and push down on a hard flat surface for a flush fit.

Inspired by @libb_s - you should check out some of their models

If you like this design I now have a MagSafe version and an Apple Watch Stand uploaded to Maker World

https://makerworld.com/en/models/132925#profileId-144122

https://makerworld.com/en/models/137254#profileId-149348

Comment & Rating (2529)

@talalas

Print Profile

0.2mm layer, 2 walls, 8% infill

perfect with pla mate and pla glow

@Dukester

Print Profile

0.2mm layer, 2 walls, 8% infill

the colors caught my eye, so i gave it a go, printed in white Ziro matte PLA at sport speeds and used a red matte PLA for the accents, they are a tight fit but thats in a good way, looks great and works great too. only suggestion would be to mirror 1 piece on the second plate so you can get the same top or bottom surfaces facing outwards when its all assembled.

(Edited)

@Reckit

looks good, sorry I thought I had mirrored the accents. will change my profile

@Reckit

Profile changed to have mirrored accents

@s.deschamps.it

Nice choice of color

@RolfHahil

Boosted

Print Profile

Merged Accent Version for AMS

I realy like it. I used PLA-Silk-Copper and charcoal black. I put a little "race-line" in the middle. looks very nice. Sadly the picture shows only half of the beauty.

@flynna431981

how did you do the "go faster stripe"

@RolfHahil

Boosted

Replying to @flynna431981 :

"go faster" :D:D:D I did it with the slicer. There you can change color your print any way you like.

@AirJ

Boosted

Replying to @RolfHahil :

Sorry if this sounds like a silly question, but did you make the modification using only the slicer (Bambu Studio?) without using the AMS?

@Rostopinto

Great job !!!

The designer has replied

@Reckit

Love the red and the yellow versions

@WingArt

Print Profile

0.2mm layer, 2 walls, 8% infill

This Design is a true piece of art - i adore it! ❤️

@Reckit

Thank you! That means a lot.

@user_2506949899

Print Profile

0.2mm layer, 2 walls, AMS requiered, race-line

Great looking stand. Printed easy. Matches my headphone stand perfectly. I put little rubber feet on the bottom because it was pretty slippery on my wood desk. Sunlu Black and Bambi matte orange.

@itsPaul19

super nice model, thank you!

@stevel85

Print Profile

0.2mm layer, 2 walls, 8% infill

Sehr schönes Modell und perfektes Druckprofil und Druckergebnis. Habe nichts abgeändert. Das kleine (bei mir weiße) Profile muss mit bisschen Kraft und Gefühl in die Halterung gedrückt werden. passt hervorragend und kann nicht rauslassen.

@h1ckman

Print Profile

0.2mm layer, 2 walls, 8% infill

printed well and i love the design. but i am going to have to reprint it. the brim on the color piece didn't remove at all and even with clean up, it looks junky now. here is hoping printing without a brim works or maybe change the distance or use support filament, if it works for that. Edit: from 4 to 5 stars. pro tip, print inserts without brim.

(Edited)

@Reckit

it actually prints fine without a brim, I added one because more people would have issues without it. Try printing without but if you have and X1 or P1S make sure you turn the aux fan completely off